HomeMy WebLinkAboutX2019-1709 - Alternative Material & MethodsX2-0tq-1"109
2i -las
CITY OF NEWPORT BEACH
COMMUNITY DEVELOPMENT DEPARTMENT
BUILDING DIVISION
100 Civic Center Drive I P.O. Box 1768 1 Newport Beach, CA 92658-8915
www newoortbeachca gov 1 (949) 644-3200
CASE NO.:'
ppr+ wwi+X y.
rfi�CEIVZ4) �,
COf,1p'UNIT1,(
APR ® 9 2020
clTy Or
A,
FORT BcPG"�
❑ REQUEST FOR MODIFICATION TO PROVISIONS
OF TITLE 9 (FIRE CODE) OR TITLE 15 (BUILDING CODE)
FOR STAFF USE ONLY
Plan Check # !223-2D/ # of Stories
OF THE NEWPORT BEACH MUNICIPAL CODE
(See Reverse for Basis for Approval) (Fee $304)
Occupancy Classification R-3 / tJ
U REQUEST FOR ALTERNATE MATERIAL
Use of Building :TF P_ # of Units
OR METHOD OF CONSTRUCTION
Project Status /Al PL- GH6o1L
(See Reverse for Basis for Approval) (Fee $304)
Construction Type V.R
❑ REQUEST FOR EXEMPTION FROM DISABLED
Verified by dL
ACCESS DUE TO PHYSICAL OR LEGAL
No. of Items /
CONSTRAINT (Fee $1,692)
Fee due 4 3
(Ratification by the Board of Appeals will be required.)
DISTRIBUTION:
❑ Owner [3Plan Check G%IP
For above requests, complete Sections 1, 2 & 3
❑ Petitioner ❑ Inspector
below by printing in ink or typing.
❑ Fire ❑ Other
1 JOB ADDRESS:
PETITIONER ADDRESS:
SITE ADDRESS: 2415 Port Whitby
William Azzalino Architect, LLC
Owner Troy BUttS _
Petitioner
(Petrttoner to be architect or engineer)
Address 2415 Port Whitby
Address 2407 Port Whitby
Newport Beach, CA zio92660
Newport Beach, CA zip 92660
Daytime Phone 714 )418-6321
_ _
Daytime Phone 1949 903-4033
2 REQUEST: Submit plans if necessaryto illustrate request. Additional sheets or data may be attached.
We are requesting to use Sika MB Topping Epoxy Coating to be applied over the existing slab
over the habitable areas (see attached) to meet the capillary break requirements of California
Green Code Section 4.505.2.1.
3 JUSTIFICATION/FINDINGS OF EQUIVALENCY:
CODE SECTIONS:
CG 4.505.2.1
The epoxy applied over the existing slab provides a capillary break to meet California Code
Section 4.505.21. and is stated to meet the requirements for the city of Newport Beach as part of
Plan Check No. Rev20-0422.
Position Architect
Petitioner's -
Signature CA Professional LIG. aF 022770 Date 4/9/2020
FOR STAFF USE ONLY
DEPARTMENT ACTION: In accordance with: ❑ CBC 104.11/CFC 104.9 ❑ CBC 104.10/CFC 104.8
(Alternate materials & methods) (CBC Modification)
❑ Concurrence from Fire Code Official is required. ❑ Approved ❑ Disapproved ❑ Written Comments Attached
BY Date
❑ Request (DOES) (DOES NOT) lessen any fire protection requirements.
❑ Request (DOES) (DOES NOT) lessen the structural integrity
The Request is Granted El Denied (See reverse for
❑ Granted (Ratification required) appeal information)
Conditions of Approval:
Signature Position CHtFP R1 to ntntr• n L Date �y- - .- 2.�
''
Print Name t
APPEAL OF DIVISION ACTION TO THE BUILDING BOARD OF APPEALS (See Reverse)
(Signature, statement of owner or applicant, statement of reasons for appeal and filing fees are required.)
CASHIER RECEIPT NUMBER: Formslmodif 12117/19
2�1�s Purr
..! ! r
Sikao
MB
SOLVENT FREE, EPDXY MOISTURE BARRIER
PRODUCT DESCRIPTION
Sika® MB is a 2 -component, solvent free, low viscosity,
epoxy for use under wood flooring products, self level-
ing underlayments, floating floors and other flooring sys-
tems that require protection from subfloor moisture.
USES
• Moisture barrier to help control moisture propagation
in cementitious substrates with a moisture content not
exceeding 6 % by Tramex Method and residual mois-
ture up to 100 % R.H. or 25 Ib/1,000 ft2/24 h (11.4
kg/92.9m2/24 h)
• For substrate consolidation on concrete, cement and
gypsum screeds
• Adhesion promoter for old and new adhesive residues
in conjunction with other Sika® products
• Suitable on concrete, cement, self -leveling and gypsum
substrates, OSB, plywood, quarry and terrazzo tiles,
water-soluble adhesive and cutbacks
PRODUCT INFORMATION
CHARACTERISTICS / ADVANTAGES
• Solvent -free (100 % solids)
• Easy roller applied application, low viscosity
• Convenient, easy to mix packaging
• Shorter construction periods
• Excellent penetration and stabilization of the substrate
• Reduction of adhesive consumption
• Suitable for use on floors with radiant heating
• Compatible with SikaBond® wood flooring adhesives,
Sika® Level products
• Can be used below floating floors
APPROVALS / STANDARDS
Meets ASTM F 3010
Chemical Base Two component epoxy
Packaging 2.64 gal (10 L) pail
Color Blue
Shelf Life 24 months from date of production if stored properly in undamaged sealed
containers
Storage Conditions Store dry at 50-77 °F (10-25 "C). Protect from moisture.
Density 69 Ib/ft3 (1.1 kg/I)
Product Data Sheet
Sika® MB
December 2018. Version 01.03
020512081000000017
1/4
ItX�Ii IL�I�QI►�r%I:iuTriL�I�
Shore D Hardness 7 days 83 (mixed A&B) (ASTM D-2240)
Compressive Strength 7 days 10,000 psi (69 MPa) 73 °F (23 °C)
50 % R.H.
Permeability to Water Vapor 0.06 g/m2-24hour-mmHG (ASTM E-96)
Service Temperature -40-158 7 (-40-70 °C)
APPLICATION INFORMATION
Coverage Coverage per pail
Moisture barrier 250-300 ft2 (23.2-27.9 m2)
Adhesion promoter or 400-450 ft2 (37.2-41.8 m2)
surface consolidator
(Coverage figures do not include allowance for surface profile and porosity or material waste).
Application
Recommended
Results in
50 °F (10 °C) 18 hours
Coatings
73 -F (23 -Q 8 hours
Moisture barrier only
min.1
Mirror like finish
Substrate
min. 1
Good penetration
consolidation only
tion Time Window*
Adhesion promotion
min. 1
Mirror like finish
only
* When Sika® MB is left on the substrate for more than the maximum allowable open time, the surface must be
Moisture barrier+
min.2
Mirror like finish
substrate consolidation
Moisture barrier+
min.2
Mirror like finish
adhesion promotion
MUST produce a monolithic, pinhole -free finish with a continuous film. The
need for multiple coats is directly related to surface
absorption.
Pot Life
50 7 (10 "C) — 60 minutes
68 °F (20 °C) — 30 minutes
86 °F (30 °C) — 15 minutes
Cure Time
50 °F (10 °C) 18 hours
73 -F (23 -Q 8 hours
86 7 (30 "C) 6 hours
*Minimum curing time, prior to walking on primer/or for applying Sika Bond' or Sika Level.
Application Time
OvercoatingApplica- Minimum Maximum
tion Time Window*
Sika® MB 8 hours 36 hours
(2nd coat)
* When Sika® MB is left on the substrate for more than the maximum allowable open time, the surface must be
mechanically prepared (i.e. sanded) solvent wiped before proceeding.
Product Data Sheet
Sika° MB
December 2010, Version 01.03
020512081000000017
BUILDING TRUST
2/4
APPLICATION INSTRUCTIONS
SUBSTRATE PREPARATION
• Substrate must be clean, dry, sound and homogeneous,
free from oils, grease, dust, and loose or friable
particles. Paint, laitance, and other poorly adhering
contents must be mechanically removed.
• Substrate must have an open textured surface to allow
Sika® MB to penetrate. (i.e. Blast cleaning, grinding are
considered acceptable means to achevie the desired
surface profile. Acid and chemical etching are not ac-
ceptable).
• At least 50 % of the surface area must be cleared of re-
sidual adhesive and cutbacks. (i.e. by grinding or mech-
anical substrate preparation)
• Old cutback can contain asbestos which is dangerous
for the health so do not grind, sand or blast. Refer to
the Resilient Floor Covering Institute's publication "re-
commended work practice for removal of resilient floor
coverings" for instruction.
• Minimum substrate compressive strength> 1,160 psi.
Tensile Bond strength > 116 psi at the time Sika® MB is
applied.
• Repair with Sika" Level SkimCoat or SikaQuick' mortar
before priming.
• The floor must be cleaned with an industrial vacuum
prior to installation of the Sika* MB.
• On fiber reinforced concrete, fibers should be flamed
off the surface prior to application of Sika* MB as a
moisture barrier.
• Before overall installation begins, Sika" recommends
the application of several small test patches to determ-
ine primer application requirements and acceptability
of final product performance.
MIXING
• Add one full can of component A to one full can of
component B then mix with an electric drill and mixing
(Jiffy Mixer type) paddle at a low speed to reduce air
entrainment (300-400 rpm). Using a paint stick or sim-
ilar is not sufficient to mix the primer.
• A minimum mixing time of 3 minutes shall be observed;
mixing shall continue until a homogeneous mix has
been achieved.
• Scrape sides of pail with paint stick or paddle to ensure
all contents are thoroughly mixed together.
• Unmixed material applied to the floor will not cure
properly.
APPLICATION METHOD/ TOOLS
• Apply Sika* MB uniformly (in 2 directions 90°) to the
substrate using a medium nap roller, ensuring that a
continuous coat is achieved over the entire surface
(MUST produce a mirror like finish).
• Pour contents of pail onto the floor for best working
time. Attempting to work from the pail will reduce
working time.
• When used as a moisture barrier and substrate consol-
Product Data Sheet
Sika® MB
December 2018, Version 01.03
020512081000000017
3/4
idation / adhesion promotor, prepare the substrate
mechanically as in accordance with the guidelines
stated in subtitle "Surface Preparation'. Apply the first
coat at 10 mils Apply the second coat at 15 mils in ac-
cordance with the open time*.
2 coats application: Apply the first coat at 75-115 ftz/gal
Apply the second coat at 150-225 W/gal in accordance
with the application time window*. Then follow one of
the option:
• Option 1: Broadcast to refusal with oven dried silica
sand (20/30) on the second coat immediately. Sweep
sand once the epoxy is cured. Apply Sika® Level
products on cured epoxy.
• Option 2: Apply Sika® Level -02 EZ Primer in accordance
with the application time window*. When the primer is
dry, apply Sika® Level products.
'ref. to appliction time in sections above
CLEANING OF TOOLS
• Clean all tools and application equipment with clean-
ing solvent (Xylene, MEK are effective).
• Hardened/cured material can only be removed mech-
anically.
LIMITATIONS
• Proper coverage must be used to achieve moisture bar-
rier properties.
• Will not act as a moisture barrier for gypsum screeds.
Gypsum based subfloors are very susceptible to excess
moisture and will be degraded if exposed to excess
moisture from below or above.
• Only protects from moisture coming from below the
concrete.
• Will not prevent hydrostatic pressure.
• Must not be applied to a visibly wet substrate.
• Does not prevent moisture occurring between the
epoxy and the floating floor due to secondary sources
of moisture or acclimation, e.g. water condensation.
• Is not suitable for use with bonded systems due to pos-
sible curing and adhesion problems.
• Sika® recommends the use of Sika' Level products on
top of it.
• Floor covering manufacturer's and Wood flooring man-
ufacturer's recommendations, like room humidity
levels and wood acclimation requirements should be
strictly followed.
• Sika® does not make any standing recommendations as
to the structural integrity of old adhesive residues or
subflooring materials that are not manufactured by
Sika'.
• When left on the substrate for more than the maxim-
um allowable open time of 36 hours, prior to placing
the adhesive, the surface must be thoroughly cleaned
and mechanically prepared (i.e. screened sand) and
solvent wiped. Failure to do this, may result in adhe-
sion problems. For detailed instruction contact our
Technical Service. When used in conjunction with Sika -
BUILDING TRUST
Bond', Sika® MB does not need to be broadcasted with
sand.
BASIS OF PRODUCT DATA
Results may differ based upon statistical variations de-
pending upon mixing methods and equipment, temper-
ature, application methods, test methods, actual site
conditions and curing conditions.
OTHER RESTRICTIONS
See Legal Disclaimer.
ENVIRONMENTAL, HEALTH AND SAFETY
For further information and advice regarding transporta-
tion, handling, storage and disposal of chemical
products, user should refer to the actual Safety Data
Sheets containing physical, environmental, toxicological
and other safety related data. User must read the cur-
rent actual Safety Data Sheets before using any
products. In case of an emergency, call CHEMTREC at 1-
800-424-9300, International 703-527-3887.
Sika Corporation Sika Mexicana S.A. de C.V.
201 Polito Avenue Carretera Libre Celaya Km. 8.5
Lyndhurst, N107071 Fra¢. Industrial Balvanera
Phone: 800-933-7452 Corregidora, Queretaro
Fax 201-933-6225 C.P. 76920
Phone: 52 442 2385800
Fax: 52 442 2250537
M
Product Data Sheet
Sika® MB
December, 20'18. Version 01.03
020512061000000017
LEGAL DISCLAIMER
• KEEP CONTAINER TIGHTLY CLOSED
• KEEP OUT OF REACH OF CHILDREN
• NOT FOR INTERNAL CONSUMPTION
• FOR INDUSTRIAL USE ONLY
• FOR PROFESSIONAL USE ONLY
Prior to each use of any product of Sika Corporation, its
subsidiaries or affiliates ("SIKA"), the user must always
read and follow the warnings and instructions on the
product's most current product label, Product Data
Sheet and Safety Data Sheet which are available at
usa.sika.com or by calling SIKA's Technical Service De-
partment at 800-933-7452. Nothing contained in any
SIKA literature or materials relieves the user of the oblig-
ation to read and follow the warnings and instructions
for each SIKA product as set forth in the current product
label, Product Data Sheet and Safety Data Sheet prior to
use of the SIKA product.
SIKA warrants this product for one year from date of in-
stallation to be free from manufacturing defects and to
meet the technical properties on the current Product
Data Sheet if used as directed within the product's shelf
life. User determines suitability of product for intended
use and assumes all risks. User's and/or buyer's sole
remedy shall be limited to the purchase price or replace-
ment of this product exclusive of any labor costs. NO
OTHER WARRANTIES EXPRESS OR IMPLIED SHALL AP-
PLY INCLUDING ANY WARRANTY OF MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE. SIKA
SHALL NOT BE LIABLE UNDER ANY LEGAL THEORY FOR
SPECIAL OR CONSEQUENTIAL DAMAGES. SIKA SHALL
NOT BE RESPONSIBLE FOR THE USE OF THIS PRODUCT
IN A MANNER TO INFRINGE ON ANY PATENT OR ANY
OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY OTH-
ERS.
Sale of SIKA products are subject to the Terms and Con-
ditions of Sale which are available at
https://usa.sika.com/en/group/SikaCorp/termsandcon-
ditions.htmi or by calling 201-933-8300.
Sika Canada Inc.
601 Delmar Avenue
Pointe Claire
Quebec 19114A9
Phone: 514-697-2610
Fax: 514-694-2792
4/4 BUILDING TRUST
Slkalvl B-en-U&(12-2018)-1-3.pdf