HomeMy WebLinkAboutXR2023-2132 - Alternative Material & MethodsCITY OF NEWPORT BEACH
COMMUNITY DEVELOPMENT DEPARTMENT
BUILDING DIVISION
100 Civic Center Drive I P.O. Box 1768 I Newport Beach, CA 92658-8915
www.newportbeachca.gov 1 (949) 644-3200
CASE NO.: 20 Z.3 — �j
❑ REQUEST FOR MODIFICATION TO PROVISIONS
OF TITLE 15 OF THE NEWPORT BEACH MUNICIPAL
CODE
(See Reverse for Basis for Approval) (Fee $270)
❑X REQUEST FOR ALTERNATE MATERIAL 2i
OR METHOD OF CONSTRUCTION
(See Reverse for Basis for Approval) (Fee
❑ REQUEST FOR EXEMPTION FROM DISABLED
ACCESS DUE TO PHYSICAL OR LEGAL
CONSTRAINT (Fee $1,506)
(Ratification by the Board of Appeals will be required.)
For above requests, complete Sections 1, 2 & 3
below by printing in ink or typing.
JOB ADDRESS:
SITE ADDRESS: 14 Oak Crest Lane
Owner John and Sue Hagestad
Address 14 Oak Crest Lane
Newport Beach, CA Zip 92660
Daytime Phone ( )
xt�Z0Z3 -Z I s2
III FOR STAFF USE ONLY III
Plan Check # Z U # of Stories 3T4- W
Occupancy Cla sification K-J // a
Use of Building 5-Y-K.. # of Units L
Project Status F. C:.
Construction Type
Verified by H
No. of Items 1.
Fee due
DISTRIBUTION:
Owner I Plan Check
Petitioner ❑ Inspector
❑ Fire ❑ Other
PETITIONER ADDRESS:
Petitioner David A. Purkis
(Petitioner to be architect or engineer)
Address 32521 Carreterra Drive
San Juan Capistrano, CA Zip
Daytime Phone (949 ) 661-6381
r2—IREQUEST: Submit plans if necessary to illustrate request. Additional sheets or data may be attached. I
This request is for the use of MiraDri 660/861 in combination with Macropoxy 646-100 epoxy paint for
protection of structural steel soldier pile.
OF EQUIVALENCY:
CODE SECTIONS:
AISC 360, CBC 1812.2
The plans specify Macropoxy 646-100 epoxy paint and MIRADRI 860/861 be applied to the back flange prior to�
installation. All remaining portions of pile are encased in concrete. This method provides physical and chemical
protection for steel soldier pile with epoxy coating that zinc is included in the product.
Petitioner's Position Civil Engineer
Q V 0�k
Signature CA Professional Lic. # RICE 42810 Date 06-21-23
FOR STAFF USE ONLY
DEPARTMENT ACTION: In accordance with: KCBC Appendix 104.11 ❑ CBC Appendix 104.10
(Alternate materials & methods) (CBC Modification)
❑ Concurrence from the Fire Marshal is required. ❑ Approved ❑ Disapproved ❑ Written Comments Attached
By: Date
PJIRequest (DOES (DO€S elessen any fire protection requirements.
Request (DOE (DOES NOT) lessen the structural integrity
The Request is Granted ❑ Denied (See reverse for
❑ Granted (Ratification required) appeal information)
Conditions of Approval:
-- CHIEF BUILDING OFFICIAL
Signature ` Position Date ,n(2- 2 j- ZoL3
Print Name / 'tc -e f
APPEAL OF DIVISION ACTION TO THE BUILDING BOARD OF APPEALS (See Reverse)
(Signature, statement of owner or applicant, statement of reasons for appeal and filing fees are required.)
CASHIER RECEIPT NUMBER: 7IC-01-S1-7S- 7-6-2-3 Forms\modif11/18/15
Protective
Marine
Coatings
MACRO PDXYO 646-100
FAST CURE EPDXY
PART A
PART B
PRODUCT INFORMATION
PRODUCT DESCRIPTION
MAC ROPDXY 646-100 FAST CURE EPDXY is a high solids, less than 100
g/L VOC, high build, fast drying, polyamide epoxy designed to protect steel
and concrete in industrial exposures. Ideal for maintenance painting and
fabrication shop applications. The high solids content ensures adequate
protection of sharp edges, corners, and welds. This product can be applied
directly to marginally prepared steel surfaces.
• <100 g/L VOC • Chemical resistant
• Low odor • Abrasion resistant
• Outstanding application properties
PRODUCT CHARACTERISTICS
Finish: Semi -Gloss
Color:
Mill White and a wide range
of colors available through tinting
Volume Solids:
73%±2% mixed
Mill White
Weight Solids:
83 %± 2%, mixed
Mill White
VOC (EPA Method 24):
Unreduced: <100 g/L; .83 Ib/gal
mixed
Reduced 10%: <100 g/L; .83 Ib/gal
Mix Ratio:
1:1 by volume
Recommended Spreading Rate per coat:
Minimum Maximum
Wet mils (microns) 7.0 (175) 13.6 (338)
Dry mils (microns) 5.0* (125)* 10.0* (250)*
—Coverage sq ft/gal (ml/L) 116 (2.8) 232 (5.7)
Theoretical coverage sq ft/gal 1168 (28.6)
(m2/L) @ 1 mil / 25 microns dft
NOTE: Brush or roll application may require multiple coats to
achieve maximum film thickness and uniformity of appearance.
*May be applied at 3.0-10.0 mils (75-250 microns) dft in a multi -
coat system. Refer to Recommended Systems and Performance
Drying Schedule
() 7.0
mils wet (175
microns):
@ 40°F/4.5-C
@ 77°F/25-C
@ 100°F/38-C
50% RH
To touch:
4-5 hours
2 hours
1.5 hours
To handle:
48 hours
8 hours
4.5 hours
To recoat:
minimum:
48 hours
8 hours
4.5 hours
maximum:
1 year
1 year
1 year
Cure for
service:
10 days
7 days
4 days
immersion:
14 days
7 days
4 days
If maximum recoat
time is exceeded, abrade surface before recoating.
Drying time is temperature,
humidity, and film thickness dependent.
Pot Life:
10 hours
4 hours
2 hours
Sweat -in -time:
30 minutes
30 minutes
15 minutes
Shelf Life: 36 months, unopened
Store indoors at 40°F (4.5'C) to
100-F (38-C).
Flash Point: 61-F (16-C), PMCC, mixed
Reduced lean Up: Reducer R7K111 or Oxsol 100
B58-620 SERIES
B58V620 HARDENER
RECOMMENDED USES
4.52
• Marine applications
• Fabrication shops • Refineries
• Pulp and paper mills • Chemical plants
• Power plants • Tank exteriors
• Offshore platforms • Water treatment plants
• Mill White is acceptable for immersion use for salt water and
fresh water
• Not acceptable for potable water
• Suitable for use in USDA inspected facilities
• Acceptable for use in Canadian Food Processing facilities, categories:
D3 (Confirm acceptanceof specific part numbers/rexes with your SW
Sales Representative)
• Conforms to AWWA D1020CS#5
• Approved with FIRETEX hydrocarbon coatings
PERFORMANCE CHARACTERISTICS
Substrate*: Steel
Surface Preparation*: SSPC-SP10/NACE 2
System Tested*:
1 ct. Macropoxy 646-100 Fast Cure @ 6.0 mils (150 microns) dft
'unless otherwise noted below
Test Name Test Method Results
ASTM D4060, CS17
Abrasion
wheel, 1000 cycles,
84 mg loss
Resistance
1 kg load
Accelerated
ASTM D4587, QUV-
Passes
Weathering - QUV1
A, 12,000 hours
Adhesion
ASTM D4541
1,037 psi
Rating 10 per ASTM
Corrosion
ASTM D5894, 36
D714 for blistering;
Weathering'
cycles, 12,000 hours
Rating 9 per ASTM
IDS 10 for rusting
Direct Impact
ASTM D2794
30 in. lb.
Resistance
Dry Heat Resistance
ASTM D2485
250-F (121-C)
Exterior Durability
1 year at 45' South
Excellent, chalks
Flexibility
ASTM D522,180°
Passes
blend, 3/4" mandrel
1 year fresh and salt
Passes, no rusting,
Immersion
blistering, or loss of
water
adhesion
Pencil Hardness
ASTM D3363
3H
Rating 10 per ASTM
ASTM B117, 6,500
D610 for rusting;
Salt Fog Resistance)
hours
Rating 9 per ASTM
D1654 for corrosion
Water Vapor
ASTM D1653,
1.16 grains/day
Permeance
Method B
Epoxy coatings may darken or discolor following application and curing.
Footnotes:
' Zinc Clad ll Plus Primer
www.sherwin-williams.com/protective
on back
Protective MAC RO PDXY° 646-100
& FAST CURE EPDXY
Marine
Coatings PART A B58-620 SERIES
PART B B58V620 HARDENER
,2019 PRODUCT INFORMATION 4,52
RECOMMENDED SYSTEMS
Dry Film Thickness / ct.
Mils Micron
Immersion and atmospheric:
Steel:
2 cts. Macropoxy 646-100
5.0-10.0 (125-250)
Concrete/Masonry, smooth:
2 cts. Macropoxy 646-100
5.0-10.0 (125-250)
Concrete Block:
1 ct. Kern Cati-Coat HIS Epoxy Filler/Sealer
10.0-20.0 (250-500)
as needed to fill voids and provide
a continuous substrate.
2 cts. Macropoxy 646-100
5.0-10.0 (125-250)
Atmosoheric:
*Steel:
(Shop applied system, new construction, AWWA D102, can also be
used at 3 mils (75 microns) oft when used as part of a multi -coat system)
1 ct. Macropoxy 646-100 Fast Cure Epoxy 3.0-6.0 (75-150)
1-2 cisof recommended topcoat
Steel:
1 ct. Recoatable Epoxy Primer 4.0-&0 (100-150)
2 cts. Macropoxy 646-100 5.0-10.0 (125-250)
Steel:
1 ct. Macropoxy 646-100
M-10.0
(75-250)
1-2 cts. Acrolon 218 Polyurethane
3.0-6.0
(75-150)
or Hi -Solids Polyurethane
3.0-5.0
(75-125)
or SherThane 2K Urethane
2.0-4.0
(50-100)
Steel:
2 cts. Macropoxy 646-100 5.0-10.0 (125-250)
1-2 cts. Tile -Clad HS Epoxy 2.5-4.0 (63-100)
Steel:
1 ct.
Zinc Clad II Plus
3.0-6.0
(75-150)
1 ct.
Macropoxy 646-100
3.0-10.0
(75-250)
1-2 cts.
Acrolon 218 Polyurethane
3.0-6.0
(75-150)
Steel:
1 ct.
Zinc Clad III HS
3.0-5.0
(75-125)
or
Zinc Clad IV
3.0-5.0
(75-125)
1 ct.
Macropoxy 646-100
3.0-10.0
(75-250)
1-2 cts. Hi -Solids Polyurethane-100
3.0-6.0
(75-150)
Aluminum:
2 cts. Macropoxy 646-100 5.0-1M (125-250)
Galvanizing:
2 cts. Macropoxy 646-100 5.0-10.0 (125-250)
The systems listed above are representative of the producfs use, other
systems may be appropriate.
DISCLAIMER
The information and recommendations set forth in this Product Data Sheet are
based upon tests conducted by or on behalf of The Sherwin-Williams Company.
Such information and recommendations set forth herein are subject to change and
pertain to the product offered at the time of publication. Consult your Sherwin-
Williams representative to obtain the most recent Product Data Information and
Application Bulletin.
SURFACE PREPARATION
Surface must be clean, dry, and in sound condition. Remove all oil, dust,
grease, dirt, loose rust, and other foreign material to ensure adequate
adhesion,
Refer to product Application Bulletin for detailed surface preparation in-
formation.
Minimum recommended
surface preparation:
Iron & Steel
Atmospheric:
SSPC-SP2/3
Immersion:
SSPC-SP10/NACE 2, 2-3 mil (50-75 micron) profile
Aluminum:
SSPC-SP1
Galvanizing:
SSPC-SP1
Concrete & Masonry
Atmospheric:
SSPC-SP13/NACE 6, or ICRI No. 310.2R,
CSP 1-3
Immersion:
SSPC-SP13/NACE 6-4.3.1 or 4.3.2, or
ICRI No. 310.2R, CSP 1-3
Surface Preparation Standards
Condition of IS08501-1
Surface BS7079-Al SSPC NACE
White Metal
Sa 3 SP 5 1
Near White Metal
Sa 2.5 SP 10 2
Commercial Blast
Be 2 Bps 3
Brush -Off Blast
Sal SP 7 4
Hand Tool Cleaning
Rusted C St 2 SP 2
Pitted & Rusted D St 2 SP 2
Power Tool Cleaning Rusted CSt3 SP3 =
Pitted & Bd Dgt3 SP3
TINTING
Tint PartAwith Maxitoners at 150% strength. Five minutes minimum mixing
on a mechanical shaker is required for complete mixing of color.
Tinting is not recommended for immersion service.
APPLICATION CONDITIONS
Temperature: 40°F (4 5°C) minimum, 140°F (60"C) maximum
(air, surface, and material)
At least 5°F (2.8°C) above dew point
Relative humidity: 85 % maximum
Refer to product Application Bulletin for detailed application information.
ORDERING INFORMATION
Packaging:
Part A: 1 gallon (3.78L) and 5 gallon (18.91 containers
Part B. 1 gallon 3.78L and 5 gallon (18.9L) containers
Weight 13.24 t 0.2 Ib/gal ; 1.61
mixed, may vary by color
SAFETY PRECAUTIONS
Refer to the MSDS sheet before use.
Published technical data and instructions are subject to change without notice
Contact your Sherwin-Williams representative for additional technical data and
instructions.
WARRANTY
The Sherwin-Williams Company warrants our products to be free of manufactur-
ing defects in accord with applicable Sherwin-Williams quality control procedures.
Liability for products proven defective, if any, is limited to replacement of the ell
tive product or the refund of the purchase price paid for the defective product as
determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
wvAy.sherwin-williams.com/protective
Protective
Marine
Coatings
APPLI
SURFACE PREPARATIONS
MAC RO PDXY° 646-100
Surface must be clean, dry, and in sound condition. Remove all
oil, dust, grease, dirt, loose rust, and other foreign material to
ensure adequate adhesion.
Iron & Steel, Atmospheric Service:
Minimum surface preparation is Hand Tool Clean per SSPC-SP2.
Remove all oil and grease from surface by Solvent Cleaning per
SSPC-SP1 For better performance, use Commercial Blast Cleaning
per SSPC-SP6/NACE 3, blast clean all surfaces using a shayp, angular
abrasive for optimum surface profile (2 mils / 50 microns). Prime any
bare steel within 8 hours or before flash rusting occurs.
Iron & Steel, Immersion Service:
Remove all oil and grease from surface by Solvent Cleaning per
SSPC-SP1. Minimum surface preparation is Near White Metal Blast
Cleaning per SSPC-SP10/NACE 2. Blast clean all surfaces usingg a
sharp, angular abrasive for optimum surface profile (2-3 mils / 50-75
microns). Remove all weld spatter and round all sharp edges by grind-
ing. Prime any bare steel the same day as it is cleaned.
Aluminum
Remove all oil ggrease, dirt, oxide and other foreign material by Solvent
Cleaning per SSPC-SP1.
Galvanized Steel
Allow to weather a minimum of six months prior to coatingg. Solvent
Clean per SSPC-SP1(recommended solvent is VM&P Naphthal When
weathering Is not possible, or the surface has been treated wl h chro-
mates or silicates, first Solvent Clean per SSPC-SP1 and apply a test
patch. Allow paint to dry at least one week before testing adhesion. If
adhesion is poor., brush blasting per SSPC-SP7 is necessary to remove
these treatments Rusty galvanizing requires a minimum of Hand Tool
Cleaning per SSPC-SP2, prime the area the same day as cleaned.
Concrete and Masonry
For surface preparation, refer to SSPC-SP13/NACE 6, or ICRI No.
310.2R, CSP 1-3 Surfaces should be thoroughly clean and dryy.
Concrete and mortar must be cured at least 28 days @ 75°F (24°C).
Remove all loose mortar and foreign material. Surface must be free
of Iaitance, concrete dust, dirt, form release agents, moisture curing
membranes, loose cement and hardeners. Fill bug holes, air pockets
and other voids with Steel -Seam FT910.
Concrete, Immersion Service:
For surface preparation, refer to SSPC-SP13/NACE 6. Section 4.3.1
or 1.3.2 or ICRI No. 3102R, CSP 1-3,
Follow the standard methods listed below when applicable:
ASTM D4258 Standard Practice for Cleaning Concrete.
ASTM D4259 Standard Practice for Abrading Concrete.
ASTM D4260 Standard Practice for Etching Concrete
ASTM F1869 Standard Test Method for Measuring Moisture Vapor
Emission Rate of Concrete.
SSPC-SP 13/Nace 6 Surface Preparation of Concrete.
ICRI No. 310.2R Concrete Surface Preparation.
Previously Painted Surfaces
If in sound condition, clean the surface of all foreign material. Smooth,
hard or glossy coatings and surfaces should be dulled by abrading the
surface. Apply a test area, allowing paint to dry one week before testing
adhesion. If adhesion is poor., or if this product attacks the previous
finish, removal of the previous coating may be necessary. It paint is
peeling or badly weathered, clean surface to sound substrate and treat
as a new surface as above.
Surface Preparation Standards
Condition of IS08501-1
Surface BS7079:Al SSPC NACE
White Metal Sa 3 SP 5 1
Near White Metal Sa 2.5 SP 10 2
Commercial Blast Sa 2 SP 6 3
Brush -OH Blast Be 1 SP 7 4
Hand Tool Cleaning Rusted C St 2 SP 2
Pitted & Rusted 0 St 2 SP 2
Power Tool CleaningRusted C St 3 SP 3
PH tl&R ttl nct P
FAST CURE EPDXY
PART A B58-620 SERIES
PART B B58V620 HARDENER
J BULLETIN 4.52
APPLICATION CONDITIONS
Temperature. 40°F (4.5°C) minimum, 140°F (60°C)
maximum
(air, surface, and material)
At least 5°F (2.8'C) above dew point
Relative humidity: 85% maximum
APPLICATION EQUIPMENT
The following is a guide. Changes in pressures and tip sizes may
be needed for proper spray characteristics. Always purge spray
equipment before use with listed reducer. Any reduction must be
compliant with existing VOC regulations and compatible with the
existing environmental and application conditions.
Reducer/Clean Up ...........Reducer R7K111 or Oxsol 100
Airless Spray
Pump..... ..............
....
....... 30:1
Pressure ......... _....
...... ...2800 - 3000 psi
Hose ..... ...... ....................1/4"
ID
Tip ......... ...... ....... .............017"
- .023"
Filter.... ................
..........60 mesh
Reduction .......................As
needed up to 10% by volume
Conventional Spray
Gun ........ ...................DeVilbiss
MBC-510
Fluid Tip- . ...... ..... ......
E
Air Nozzle... ........... .._,....704
Atomization Pressure.....60-65
psi
Fluid Pressure._.............10-20
psi
Reduction .......................As
needed up to 10% by volume
Requires oil and moisture
separators
Brush
Brush ,... ............ ..........._,Nylon/Polyester or Natural Bristle
Reduction .......................Not recommended
Roller
Cover.............................3/8" woven with solvent resistant core
Reduction .......................Not recommended
If specific application equipment is not listed above, equivalent
equipment may be substituted.
www,shemin-williams.com/protective
continued on back
Protective MACROPDXY° 646-100
& FAST CURE EPDXY
Marine
Coatings PART A B58-620 SERIES
PART B B58V620 HARDENER
.2019 APPLICATION BULLETIN 4.52
APPLICATION PROCEDURES
Surface preparation must be completed as indicated.
Mix contents of each component thoroughly with low speed power
agitation. Make certain no pigment remains on the bottom of the
can. Then combine one part by volume of Part A with one part
by volume of Part B. Thoroughly agitate the mixture with power
agitation. Allow the material to sweat -In as Indicated prior to ap-
plication. Re -stir before using.
If reducer solvent is used add only after both components have
been thoroughly mixed, after sweat -in.
Apply paint at the recommended film thickness and spreading
rate as indicated below:
Recommended SDreadina Rate Der coat:
Minimum Maximum
Wet mils (microns) 7.0 (175) 13.5 (338)
Dry mils (microns) 5.0" (125) 10.0" (250)'
—Coverage sq ft/gal (l/L) 116 (2.8) 232 (5.7)
Theoretical coverage sq ft/gal 1168 (28.6)
(m-/L) @ 1 mil / 25 microns oft
NOTE: Brush or roll application may require multiple coats to
achieve maximum film thickness and uniformity of appearance.
`May be applied at 3.0-10.0 mils (75-250 microns) dft in a multi -
coat system. Refer to Recommended Systems and Performance
Drying Schedule (ril 7.0
mils wet (175
microns):
@ 40-F/4.5-C
@ 77-F/26-C
@ 100"F/38°C
50% RH
To touch:
4-5 hours
2 hours
1.5 hours
To handle:
48 hours
8 hours
4.5 hours
To recoat:
minimum:
48 hours
8 hours
4.5 hours
maximum:
1 year
1 year
1 year
Cure for
service:
10 days
7 days
4 days
immersion:
14 days
7 days
4 days
If maximum recoat
time is exceeded, abrade surface before recoating.
Drying time is temperature, humidity, and film thickness dependent.
Pot Life:
10 hours
4 hours
2 hours
Sweat -in -time:
30 minutes
30 minutes
15 minutes
Application of coating above maximum or below minimum
recommended spreading rate may adversely affect coating
performance.
CLEAN UP INSTRUCTIONS
Clean sppills and spatters immediately with Reducer R7K111 or
Oxsol 100. Clean tools Immediately after use with Reducer R7K111
or Oxsol100. Follow manufacturer's safety recommendations
when using any solvent.
DISCLAIMER
The information and recommendations set forth in this Product Data Sheet are
based upon tests conducted by or on behalf of The Sherwin-Williams Company.
Such information and recommendations set forth herein are subject to change and
pertain to the product offered at the time of publication. Consult your Sherwin-
Williams representative to obtain the most recent Product Data Information and
Application Bulletin.
PERFORMANCE TIPS
Stripe coat all crevices, welds, and sharp angles to prevent early failure
in these areas.
When using spray application, use a 50% overlap with each pass of the
gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray
at a right angle
Spreading rates are calculated on volume solids and do not include an
application loss factor due to surface profile, roughness or porosity of the
surface, skill and technique ofthe applicator, method ofapplication, various
surface irregularities, material lost during mixing, spillage, overthinning,
climatic conditions, and excessive film build.
Excessive reduction of material can affect film build, appearance, and
adhesion.
Do not mix previously catalyzed material with new.
Do not apply the material beyond recommended pot life.
In orderto avoid blockage of spray equipment, clean equipment before use
or before periods of extended downtime with Reducer R71<111 or Oxsol 100.
Insufficient ventilation, incomplete mixing, miscatalyzation, and external
heaters may cause premature yellowing.
Excessive film build, poor ventilation, and cool temperatures may cause
solvent entrapment and premature coating failure.
Tinting is not recommended for immersion service.
Use only Mil White for immersion service
ouik-Kick Epoxy Accelerator is acceptable for use. See data page 4.99
for details.
Application of coating above maximum or below minimum recommended
spreading rate may adversely affect coating performance.
For Immersion Service: (if required) Holiday test in accordance with
ASTM D5162 for steel, or ASTM D4787 for concrete.
When coating over steel in a. zinc/epoxy/epoxy, or epoxy/epoxy/epoxy
system, Macropoxy 646-100 must be applied at a minimum dft of 3.0
mils per coat.
Acceptable for Concrete Floors.
Refer to Product Information sheet for additional performance charac
teristics and properties.
SAFETY PRECAUTIONS
Refer to the MSDS sheet before use.
Published technical data and instructions are subject to change without notice
Contact your Sherwin-Williams representative for additional technical data and
instructions.
WARRANTY
The Sherwin-Williams Company warrants our products to be free of manufacturing
defects in accord with applicable Sherwin-Williams quality control procedures.
Liability for products proven defective, if any, is limited to replacement of the de-
fective product or the refund of the purchase price paid for the defective product
as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
www.sherwin-williams.com/pmtective
MiriDri 860 Self -Adhered
Waterproofing Membrane
or approved equivalent.
Apply over steel flange
PT Wood Lagging treated with Macropoxy
for shoring 646-100.
per shedule (TS2)
MiraDrian Panel
MiraClay membrane
lap tight against MiraDrain Miradrian Panel
& wide flange (typ.)
Wide Flange Pile
per Schedule (TS2)
Typical Flange Treatment Detail
SCIENCE.. SERVICE. SOLUTIONS.
MIRADRI® 860/861
Description
CCW MiraDR1860/861 is a self -adhering sheet membrane consisting
of 56 mils (1.4 mm) of rubberized asphalt laminated to 4 mils (0.1 mm)
of polyethylene to form a minimum 60-mil (1.5 mm) membrane. The
combination of these two excellent waterproofing materials provides a
high-performance, extremely durable waterproofing barrier MiraDRI
860/861 is suitable for installations where the ambient temperature is
40"F (4.4°C) or above. MiraDRI 860-861 can be used for applications
between 25°F (-3.9°C) and 40°F (4.4°C) if the product is stored in a heated
area until use and the laps are treated with CCW contact adhesive.
MuaDRI 860/861 membrane is used for vertical and horizontal
waterproofing on structural foundation walls and decks. Below -grade
foundation walls, tunnels,. split slabs, plaza decks and parking decks are
all areas where MiraDRI 860/861 may be applied. MiraDRl 860/861 also
may be used In Interior areas such as mechanical rooms, laboratories,
kitchens and bathrooms, MiraDRI 860/861 should be covered with either
CCW 200V/300HV Protection Course, CCW Protection Board, or CCW
MiraDRAIN" drainage composites.
Installation
Temperature: Typical installation of MiraDRI 860/861 can be performed
when ambient and substrate temperatures are 40°F and above.
Installations below 40°F are best addressed with MiraDRI 860 ULT
(ultra low temperature adhesive formula). However. installation between
25°F - 40°F may be performed if the MiraDRI 860/861is stored in
a heated area until use and the laps are treated with CCW contact
adhesive. Consult your local CCW Technical Representative and the
MiraDRI 860 ULT product data sheet for further information,
Preparation: Do not apply MiraDRI 86C/861 to frozen or wet substrates.
The membrane should not be left exposed to direct sunlight for longer
than 14 days. MiraDRI 860/861 can be applied to concrete, metal, wood,
insulated wall systems or masonry surfaces. All substrates must be clean,
dry and free of surface irregularities.
Concrete Substrates: Structural concrete must be cured a minimum of
7 days and lightweight structural concrete must cure a minimum of 14
days before the application of MiraDRI 860/861, Repair surfaces that are
not structurally sound or have voids, protrusions, rough spelled areas,
loose aggregate or exposed course aggregate. Any voids exceeding Yd'
COAT/NOS Q W4TERRFi CL
in width should be filled with latex Portland cement., concrete or epoxy
concrete and troweled smooth to match the existing surface, Protrusions
and other rough areas should be broken off and patched as above. CCW
LM 800XL CCW 201, or CCW 703V may be used to fill small voids,
honeycombs or bug holes,
Masonry Substrate: Apply MiraDRI 860/861 waterproofing over
concrete block with smooth trowel -cut mortar joints or rough surfaces
prepared with a parge coat. Allow the parge coat to dry before priming
and installing the MiraDHI 860/861 waterproofing membrane.
Chemical Additives: Concrete shall be cured by water curing method.
Any curing compounds must be of the pure sodium silicate type or clear
resin -based materials without waxes., oils or pigments and be approved by
the Carlisle representative, Form release agents must not transfer to the
concrete. Remove forms as soon as possible from below horizontal slabs
to prevent entrapment of excess moisture. Excess moisture may lead to
blistering of the membrane. Curing compounds or form release agents
that adversely affect theadherence of the MiraDRI 860/861 waterproofing
membrane must be removed from the substrate prior to application.
Priming: All concrete, metal. masonry, wood and sheathing substrates
require CCW Contact Adhesive, Insulated concrete forms require a
water -based CCW Contact Adhesive, Carlisle Coatings & Waterproofing
recommends an adhesion test of the MiraDRI 860/861 on any bare
substrate to verify proper adhesion. Apply the appropriate CCW Contact
Adhesive at the specified coverage rate. Apply Contact Adhesive with a
lambswool roller, brush or spray apparatus. Allow Contact Adhesive to
dry for a minimum of 30 minutes, The CCW Contact Adhesive will dry to a
tacky finish. Areas primed with a CCW Contact Adhesive but not covered
with MiraDRI 860/861 within the same day must be re -primed.
When installing CCW sheet membranes and sheet flashings over gyp -
sheathing with glass -mat facers, coverage rates for contact adhesives
and primers will depend on the porosity and texture of the sheathing and
will vary substantially by gypsum -sheathing brand and manufacturer.
To achieve consistent contact adhesive and/or primer coverage with
adequate tack, it may be necessary to decrease the coverage rate (i.e.
increase the amount applied) of the contact adhesive and/or primer and/
or the application of multiple coats. CCW Contact adhesives and primers
shall be allowed to dry completely (lower temperatures will extend
drying time) before additional coats are applied or membrane installed.
Caution should be taken as contact adhesives and/or primers applied to
Carlisle Coatings & Waterproofing
900 Hensley Lane I Wylie, TX 75098 1 800.527.7092 1 www.carlislecew.com
SCIENCE. SERVICE. SOLUTIONS.
MIRADRI 860/861
gyp -sheathings with glass -mat facers will take longer to dry than other
substrates. Multiple adhesion tests should be performed randomly to
verify proper application of primer and ensure a successful application.
Detailing: All vertical -to -horizontal transitions must have a'/a" (19.05
mm) fillet of CCW LM-800XL. CCW-201 Sealant or CCW-703V Liquiseal.
Allow CCW-LM-800XL to cure 1 hour, CCW-703V to cure 4 hours,
CCW-201 to cure 16 hours before covering with the MiraDRI 860/861
membrane. All inside and outside corners, as well as the vertical -to -
horizontal transitions, should have a minimum 9" detail strip of MiraDRI
860/861 installed prior to the field membrane of MiraDRI 860/861, The
MiraDRI 860/861 Membrane Strip should be centered on corners, joints,
cracks and transitions, After field membrane is installed, a sealant bead
of CCW LM-800XL. CCW-704, CCW-201, or CCW-703V should all be
placed over all laps at the footing/wall transition extending a minimum
of 9" up the wall and 9" out over the footing. Refer to the standard detail
drawings for specific detail instructions.
Vertical Installation
Start at the low point and work towards the high point, Remove
6''-8" (150-200 mm) of the release paper, and then begin applying
the membrane. Press and smooth the membrane against the substrate
while pulling the release paper free. Roll entire membrane and laps with
a hard rubber hand roller Install membrane with side laps overlapped a
minimum of 2/2' (63 mm) and end laps a minimum of 5" (127 mm). CCW
recommends that the membrane be rolled in place immediately after its
placement to ensure full adhesion to the primed substrate. Apply a bead
of CCW 704, CCW LM 800XL, or CCW 703V Liquiseal at terminations,.
cut edges, T-joints, drains, penetrations. CCW 704 Mastic should not be
installed on the underside of CCW Miradri 860/861. For walls over 8' (240
cm), the membrane should be placed in lifts, Protect the MIraDRI 860/861
membrane with the appropriate CCW MiraDRAIN drainage composite, CCW
200V/30011V Protection Course, or CCW Protection Board V,
Horizontal Installation
Start at the low point (establish a starting point with a chalk line if
necessary) and work towards the high point in shingle fashion. Remove
2'-3' (60-90 cm) of the release paper and apply the membrane to
the substrate. Continue pulling the release paper free while pressing
and smoothing the membrane against the substrate. Apply in a straight
line avoiding wrinkles and over -correcting. Roll the membrane with
a minimum 75-lb. (34 kg) linoleum roller. Install membrane with side
laps overlapped a minimum of 2'/2" (63 mm) and end laps a minimum
of 5" (127 mm). Apply a bead of CCW-704 Mastic at all terminations of
the membrane and T-joints. Apply a 3/" (19,05 mm) fillet of CCW LM
800XL. CCW 201, or CCW 703V Liquiseal in all inside corners of planter
boxes, shower stalls and shower pans. Patch inadequately lapped seams
and damaged areas with MiraDRl 860/861 membrane covering the
damaged area by a minimum of 6" (150 mm). 'Fish -mouths" and severe
wrinkles should be slit., flaps overlapped and repaired as above, Protect
the MiraDRl 860/861 membrane with the appropriate CCW MiraDRAIN
drainage composite or CCW 300HV Protection Course.
Detail Requirements: For standard installation details follow the
MiraDRI 860/861 details drawings. For non-standard installation
instructions contact your local CCW representative.
Limitations
Do not apply where membrane will be subject to continuous exposure to
sunlight. The membrane should not be left exposed to direct sunlight for
longer than 14 days.
Do not apply primer or membrane to a damp, frosty, frozen, or
contaminated surface.
Not recommended as a pond or tank liner except for between -slab
applications,
Do not apply over sealants containing coal tar or polysulfides. In the event
of existing bitumen- modified materials,. consult your CCW representative.
Warnings and Hazards
CCW Contact Adhesives, Mastics and Sealants may contain flammable
and combustible solvents. Avoid exposure to open flame or spark. Avoid
breathing vapors. Use only in areas with adequate ventilation, Refer to
MSDS for important warnings and product information.
Packaging
Irr
I
CCW MiraDRI 860/861
36" wide x 67' roll (200 He)
25 rolls/pallet(5000 fta)
Weight = 80lb/roll (approx.)
CCW-702LV VOC-Compliant Solvent Base
5-gallon palls (45 palls/pallet)
Contact Adhesive
CCW-702WB Water Base Contact Adhesive
5-gallon pails (45 pails/pallet)
CCW-AWP Water Base Contact Adhesive
1-gallon pails LI 00 pails/pallet)
5-gallon pails (45 pails/pallet)
CCW-702 Solvent Base Contact Adhesive
5-gallon pails (45 pails/pallet)
CCW-715 Damp Concrete Contact Adhesive
5-gallon pails (45 pails/pallot)
CCW-704 Mastic and CCW LM-800XL
30-oz Of Tube (12 tubes/carton)
5-gallon pails (45 pails/pallet)
CCW-703V Liquiseal
3.5-gal Part A/0.5-gal Part B
(45 Ibs/unit)
CCW-LM-800XL
5-gallon (19-liter) pails
29-oz. (822-kg) tubes. 12 per box
CCW-201
1.5-gallon kit (in 2-gallon pail)
Standards
• COW MiraDRI 860/861 meets the applicable requirements at:
- GSA: PBS PCD 07121
- USN: NAVFAC TS-07111
- VA; H-08-1
- Federal Construction Guide Specs; FCGS-07111
- Corps of Engineers. LEGS-07111-3-82
- UL 790, Class A
- LA Research Report Number 25094L
COATINGS 6 WATEFIPROQFING
Typical Properties
II
II
Color
—
Dark Gray
Thickness
ASTM D3767
60 mils
Tensile (Membrane)
ASTM D412
325 psi
Tensile (Film)
ASTM D882
5000 psi
Elongation
ASTM D412
350%
Permeance
ASTM E96
0.05 perms
Low Temp, Flexibility'
ASTM D1970
Unaffected
Crack Cycling'
ASTM C836
Unaffected
Peel Strength
ASTM D903
10.0 lb/in
Lap Adhesion
ASTM D1876
19.0 lb/in
Puncture Resistance
ASTM E154
601b (min)
Soil Burial at 16 wks
GSA -PBS 07121
No effect
Water Absorption
ASTM D570
,10.1 a/by wt
Hydrostatic Head
ASTM D5385
230 H
180 deg rend over a 1 (25 mn) mandrel at-45-FI43°C1
100 cycles at 25-F(-32'C1
SCIENCE. SERVICE. SOLUTIONS.
COATINGS 6 WATERPROOFING
MIRADRI 860/861
Limited Warranty
Carlisle Coatings & Waterproofing Incorporated (Carlisle) warrants this product
to be free of defects in workmanship and materials only at the time of shipment
from Our factory If any Carlisle materials prove to contain manufacturing defects
that substantially affect their performance, Carlisle will, at its option, replace the
materials or refund its purchase price. This limited warranty is the only warranty
extended by Carlisle with respect to its materials. There are no other warranties.
including the implied warranties of merchantability and fitness for a particular
purpose. Carlisle specifically disclaims liability for any incidental. consequential, or
other damages. Including but not limited to. loss of profits or damages to a structure
or its contents, arising under any theory of law whatsoever. The dollar value of
Carlisle's liability and buyer's remedy under this limited warranty shall not exceed
the purchase price of the Carlisle material in question.
Carlisle Coatings & Waterproofing
900 Hensley Lane I Wylie, TX 75098 1 800.527.7092 1 www,carlisleccw.com
09.14 1I Q 2017 Carlisle. Oarlola, MraCRI and MIraCRAIN are. trademarks of Cadlslc.
REPRINT CODE e01403- M I RAD9I Moen iecdnica 10 a la Shall