HomeMy WebLinkAboutS2020-0180 - Misc (2)G%2o-oif0
V f
CITY OF NEWPORT BEACH
COMMUNITY DEVELOPMENT DEPARTMENT
BUILDING DIVISION
100 Civic Center Drive I P.O. Box 1768 1 Newport Beach, CA 92658-8915
www.newportbeachca.00v 1 (949) 644-3200
2019 SWIMMING POOL & SPA
RESIDENTIAL
MINIMUM CONSTRUCTION REQUIREMENT
ENCLOSURE. BARRIER & DROWNING PREVENTION
1. Every pool and/or spa shall be fully enclosed by a barrier. Pool Barrier shall comply with the following (NBMC 15.09,
ISPSC 305.2.1 through 305.3.3):
a. 5 ft or greater height above grade, measured from outside of the pool area.
b. Minimum 45 inches spacing of horizontal members when placed on the outside of the fence.
c. Maximum 4 inch spacing of vertical members.
d. Decorative cutouts shall not exceed 1.75 inches wide.
e. Maximum 2 inch vertical clearance between the bottom of the fence and ground.
f. Maximum 1.75 inch square chain link mesh, unless provided with slats fastened at the top and bottom which
reduce the openings to 1.75 inches or less.
g. Diagonal members shall form openings of 1.75 inches or less.
h. Gates shall have self-closing, and self -latching mechanisms. Latch mechanism shall be at least 60 inches above
the ground.
i. All gates shall swing out of the pool area in the direction leading to a public way.
2. Prior to pre -plaster approval and filling pool/spa, at least two drowning prevention safety measure as noted in #3
below shall be permanently installed (CBC 3109.2 (115922)).
3. Two drowning prevention safety features shall be provided. Identify the drowning prevention safety feature to be
utilized for this pool installation (CBC 3109.2 (115922)).
a. Intermediate pool enclosure between the house and pool.
b. Removable mesh pool fencing that meets American Society for Testing and Materials (ASTM)
Specifications F2286 standards in conjunction with a gate that is self-closing and self -latching and can
accommodate a key lockable device.
c. All doors providing direct access to the pool/spa area from the residence shall be equipped with a self-closing,
self -latching device with a release mechanism placed at 54 inches or more above the floor.
d. The residence shall be equipped with exit alarms on all doors providing direct access to the pool/spa. Door
alarms shall comply with the following:
i. Door alarms shall be listed and labeled in accordance with UL 2017. (CBC 3109.4.1.8 Item 1).
ii. Alarm shall produce an audible warning when the door and/or its screen, are opened..
iii. The alarm shall sound continuously for a minimum of 30 seconds within 7 seconds after the door is opened,
at a sound pressure level of not less than 85 dBA when measured inside the dwelling at 10 ft from the
alarm. BUILDING DIVISION
iv. The alarm shall automatically reset under all conditions.
V. The alarm shall be equipped with a manual means to temporarily deactivate the alarm for a single opening.
The deactivation shall last not more than 15 seconds. The deactivation switch shall be located 1ptpast 54
inches above the threshold of the door.
vi. Alarms shall be permanently secured by screws or epoxy.
e. An ASTM Specifications F1346-91 (reapproved 2010) approved safety pool cover.
i. Product Manufacturer: BY- MIX
ii. Product Name:
iii. ASTM testing agency approval letter.
f. Swimming pool alarms that, when placed in pools, will sound upon detection of accidental or unauthorized
entrance into the water. These pool alarms shall meet and be independently certified to the ASTM Standard
F2208 "Standards Specification for Pool Alarms" which includes surface motion, pressure, sonar, laser and
infrared type alarms. For purposes of this article, "swimming pool alarms" shall not include swimming
protection alarm devices designed for individual use, such as an alarm attached to a child that sounds when
the child exceeds a certain distance or becomes submerged in water.
CorrLisls\Swimming PoolsSpaRESIOENTIALMinConslrReq 03/11/2020
4. Safety glazing is required in fences, doors and windows, where the glass is within 5 ft of the pool/spa/hat tub's edge
and less than 60 inches above grade (CBC 2406.4.5 & CRC R308.4.5).
POOL AND SPA CONSTRUCTION
1. Construction of stairs into the shallow end and recessed pool stairs shall conform to the following (ISPC 809.5):
a. Treads shall have a minimum unobstructed horizontal depth of 10 inches and a minimum
unobstructed walking surface area of 240 square inches.
b. Risers, other than the top and bot -tom riser, shall have a uniform height of not greater than 12
inches.
c. The top riser height shall be any dimension not exceeding 12 inches for the width of the walking
surface.
d. The bottom riser height shall be any dimension not exceeding 12 inches.
e. Riser heights shall be measured at the horizontal centerline of the walking surface area.
f. In design water depths exceeding 48 inches, additional steps shall not be required.
2. The slope of beach and sloping entries used as a pool entrance shall not exceed 1 unit vertical in 7 units
horizontal (14 -percent slope). (ISPC 809.6)
3. Where steps and benches are used in conjunction with sloping entries, the vertical riser distance shall not
exceed 12 inches. For steps used in conjunction with sloping entries, the requirements of Section 809.6 shall
apply. (ISPC 809.7)
4. The horizontal surface of underwater seats, benches and swimouts shall be not greater than 20 inches below
the design waterline (ISPC 809.9)
5. SPA FLOOR: The slope of the floor shall not exceed 1 unit vertical in 12 units horizontal (8.3 -percent slope).
Where multilevel floors are provided, the change in depth shall be indicated. (ISPC 904.3)
6. Where installed, steps and ladders shall be located outside of the minimum diving water envelope as indicated
LADDER/ POOL WALL
RECESSED TREADS
UNDERWATER SLOPED ENTRY
SEAT
OR SW IMOUT
BENCH
0 INTRUSIONS
STATIONARY --M\ DIVING ENVELOPE
DIVING n- DECK
PLATFORM
AND ROCKS
POOL WALL STAIRS WITH SEAT
SIDE OR DEEP END STEP
FIGURE 322.2
MINIMUM WATER DIVING ENVELOPE
7. LADDERS: Ladder treads shall have a uniform horizontal depth of not less than 2 inches. There shall be a uni-
form distance between ladder treads, with a distance of not less than 7 inches and not greater than 12 inches.
The top tread of a ladder shall be located not greater than 12 inches below the top of the deck or coping. Ladder
treads shall have slip -resistant surfaces. (ISPC 322.3)
a. There shall be a clearance of not less than 3 inches and not greater than 6 inches between the
pool wall and the ladder.
b. Ladders shall be provided with two handholds or two handrails. The clear distance between ladder
handrails shall be not less than 17 inches and not greater than 24 inches.
8. RECESSED TREAD: Recessed treads shall have a mini -mum depth of not less than 5 inches and a width of
not less than 12 inches. The vertical distance between the pool coping edge, deck, or step surface and the
uppermost recessed tread shall be not greater than 12 inches. Recessed treads shall have slip -resistant
surfaces. (ISPC 322.4)
ConLists\SwlmmingPoolsSpaRESIDENTIALMInConstrRaq 03/11/2020
a. Recessed treads at the center -line shall have a uniform vertical spacing of not less than 7 inches
(178 mm) and not greater than 12 inches.
b. Recessed treads shall drain into the pool.
c. Recessed treads shall be provided with a handrail or grab rail on each side of the treads. The clear
distance between handrails and grab rails shall be not less than 17 inches and not greater than 24
inches.
ELECTRICAL SYSTEM
1. Any walk surface within 3 ft of the pool edge shall be bonded, including unreinforced or landscaped areas. (CEC
680.26.(B)(2))
2. In outdoor pool areas, luminaires, lighting outlets, and ceiling -suspended (paddle) fans installed above the pool or
the area extending 5 ft. horizontally from the inside walls of the pool shall be at a height not less than 12 ft. above the
maximum water level of the pool.
3. Electrical outlets less than 20 ft from pool or spa shall be GFCI protected (CEC 680.22.(A)(4)).
4. All overhead power lines and other services shall comply with CEC 680.9.
5. The following devices and equipment associated with the swimming pool, spa, or hot tub shall be grounded in
accordance with CEC, Article 680.6:
a. Underwater Lighting
b. Electrical equipment and panel boards
c. Ground fault circuit interrupters
6. The following structures and equipment shall have electrical bonding (CEC 680.26):
a. Pool shell reinforcing or metal shell
b. Underwater lighting
c. Metal fittings attached to pool structure
d. Electrical equipment including pumps, motors, & electric pool covers
e. Fixed metal parts/structures (i.e. metal sheathed cables, pipings, awnings, fences, etc...) less than 5 ft
horizontally measured from inside pool wall
f. Fixed metal parts/structures (i.e. metal sheathed cables, pipings, awnings, fences, etc...) less than 12 ft vertically
above highest water level
g. Steel reinforcing under adjacent walking surfaces
7. The following devices and equipment associated with the swimming pool, spa, or hot tub shall be GFCI protected in
accordance with CEC Section 680:
a. Receptacles located within the general area of a pool, spa, or hot tub
b. Receptacles used for power generation for pools, spas, and hot tubs
c. Electrical equipment
PLUMBING & HEATING SYSTEMS
1. Pool system piping (CA -ENERGY 150(p)(2)):
a. A straight pipe (min. length = 4 x pipe diameter) shall be installed before the pump.
b. Pipe size shall be sized such that at maximum flow the velocity of the water is less than 8 fps in the return line
and 6 fps in the suction line.
c. All elbows shall be of sweep elbow or elbow -type that provides less pressure drop than straight pipe length of 30
pipe diameter.
d. Pool filters shall beat least the size specified in NSF/ANSI 50 for public pool intended applications. (CA -ENERGY
150(p)(3))
e. Backwash valve shall be same as return pipe diameter, but not less than 2" diameter. (CA -ENERGY 150(p)(4))
2. Pool/spa drain shall be connected to a "P" trap, which drains to the sewer system. (CPC 813.1)
3. Pool/spa heater vent shall be 4 ft away from property line. The equipment vent shall be 4' away or one foot above
openings in dwelling exterior walls. (CMC 802.8.2)
4. Pool/spa heating system shall be certified by the manufacturer for the following items (CA -ENERGY 110.4(a)):
a. Thermal efficiency complies with Appliance Efficiency Regulations
b. On-off switch mounted outside of the heater
c. A permanent weatherproof instruction plate or card for energy efficient operation
d. No electric resistance heating
5. Wastewater from any filter, scum filter, scum gutter, overflow, pool emptying line, or similar apparatus shall discharge
3
CorrLists\Swimming PoolsSpaRESICENTIALMinConslrRoq 03/11/2020
into an approved type receptor and subsequently into a public sewer. The flood level rim of such receptor shall be at
least 6 inches above the Base Flood Elevation (BFE) indicated in the Flood Insurance Rate Map (FIRM) as printed
by the Federal Emergency Management Agency's with effective date of 3-21-2019. Direct connections shall not be
made between the end of the backwash line and the disposal system. Drains shall discharge through an air gap.
(ISPSC 320.1)
6. New swimming pool/spa shall have at least two circulation suction outlets per pump that shall be hydraulically
balanced and symmetrically plumbed through one or more "T" fittings, which are separated by a distance of at least
3 ft in any direction between the drains. (CBC 3109.2 (115928)(a)(2))
7. Suction outlets shall be covered with anti -entrapment grates, as specified in the ANSI/APSP-16 performance
standard or successor standard designated by the federal Consumer Product Safety Commission that cannot be
removed except with the use of tools. Slots or openings in the grates or similar protective devices shall be of a shape,
area, and arrangement that would prevent physical entrapment and would not pose any suction hazard to bathers.
(CBC 3109.2 (115928.(b)))
8. Surface skimming systems shall be listed and labeled in accordance with NSF 50.
PUMPS & MOTORS
1. An emergency shutoff switch shall be provided to disconnect power to recirculation and jet system pumps and air
blowers. Emergency shutoff switches shall be: provided with access; located within sight of the pool or spa; and
located not less than 5 feet horizontally from the inside walls of the pool or spa.
2. All pool or spa systems and equipment shall have the following (CA -ENERGY 110.4):
a. At least 36 inches of pipe between the filter and heater, or dedicated suction and return line, or built-in connection
to allow for the future addition of solar heating equipment.
b. A cover for outdoor pools or spas if a heat pump or gas heater is used.
c. Pool shall have directional inlets to mix the pool water.
d. The circulation pump must have a time switch that allows the pump to be set to run in the off-peak electric demand
period for the minimum time required to maintain public health standards.
3. Pool pumps & motors (CA -ENERGY 150(p)(1)):
a. Only those listed in the Commission's directory of certified equipment shall be installed
b. Filtration flow rate shall not exceed that to turn over pool water volume in 6 hours or 36 gpm, whichever is greater.
c. Pump motors (for filtration) shall be multi -speed if capacity is greater than 1 hp.
d. Each auxiliary pool load (spa, water features, etc.) shall be served by a separate pump or multi -speed pump.
e. Multi -speed pump shall have controls that will default to the filtration flow rate when no auxiliary pool loads are
operating.
f. Multi -speed pump shall default to the filtration flow rate setting within 24 hours.
INSPECTION
1. Special inspection is required for shotcrete and gunite installation.
2. A sound test by an acoustical engineer is required to demonstrate that the noise level from the pump is less than 55
dBA at the property line. NBMC 10.26.025.
3. Where sulfate or salt water exposure is known to exist due to local soil conditions, concrete shall be of Type V and
shall have a compressive strength of 4500 psi min at 28 days. Epoxy coated reinforcing bars shall be required for all
shell reinforcing and bond beam bars.
CorrLisls\SwimmingPoolsSpaRESIDFNTIALMinConslrPeq 03/11/2020
Poolguard°
OPERATING INSTRUCTIONS
MANUAL
"NSF CERTIFIED TO THE ASTM SAFETY SPECIFICATION F 2208"
MODEL PGRM - 2
85dB Horn at 10 Feet
This product has been designed to aid in the detection of unwanted intrusions into
unsupervised pools. POOLGUARD IS A SAFETY ALARM SYSTEM AND NOT A
LIFE SAVING DEVICE. "This device is not intended to replace any other safety
consideration - i.e., adult supervision, lifeguards, fences, gates, pool covers, locks, etc.,
and some devices may not detect gradual entry."
CERTIFICATION
NSF International Certifies that the POOLGUARD Pool Alarm Model
PGRM-2 conforms to the requirements of ASTM F2208 - Standard
Safety Specification for Residential Pool alarms.
1. Certified to ASTM F2208-2008 for performance.
2. Certified to NSF/ANSI Standard 50 for material safety. Certified
pool and spa end use temperatures.
POOLGUARD Pool Alarm Model PGRM-2 will meet or exceed all parts
of the Tennessee Pool Alarm requirements of the Katie Beth Law.
INSPECTION
POOLGUARD is packaged in a shipping carton that minimizes the chance
of damage due to handling. Check for damage and confirm that the con-
tents of the carton include the following items:
• POOLGUARD Unit
• Handle
• Red Reset/Sleep Key
• Remote Receiver and Power Supply
*Operating Instructions Manual
If an item is missing, contact either the place of purchase or PBM
Industries, Inc. for replacement.
CARE AND HANDLING
POOLGUARD is constructed from sturdy plastic to withstand the adverse moisture
environment of a swimming pool. Care needs to be taken when handling to ensure
against being dropped, kicked, etc. ALWAYS REMOVE THE POOL UNIT FROM
THE POOL WHEN THE POOL IS BEING USED. STORE THE ALARM IN THE
UPRIGHT POSITION (See Figure 1) AWAY FROM POOL ACTIVITY. If the pool
unit accidentally falls into your pool, remove it immediately and drain the water
from it. Take the pool unit apart as indicated in the Battery Installation/Replacement
section and remove the battery. Remove all the water from the inside of the unit,
the battery and the circuit board area with a paper towel or cloth. Completely test
the alarm before each use as described in the manual to ensure proper operation.
CAUTION: KEEP THE RED RESET/SLEEP KEY OUT OF THE REACH OF
CHILDREN. INTERNAL MAGNET MAY BE HARMFUL IF SWALLOWED'
ATTACHING HANDLE
The two handle screws are located in the top of the alarm, remove them
and attach the handle, (See Figure 1).
OPERATING YOUR ALARM
RESET/SLEEP MODE (SEE FIGURE 1)
RESET: When the pool unit is installed in the pool and the horn is sounding; place
the red reset/sleep key on the reset/sleep decal to reset and silence the alarm. The
pool unit is now monitoring your pool for an intrusion.
SLEEP MODE: When the pool unit is removed from the pool and the horn is
sounding; place the red reset/sleep key on the reset/sleep decal for 3 to 4 seconds
to activate sleep mode and silence the alarm. To store the alarm, place the alarm in
the upright position (See Figure 1). The pool unit will automatically wake up
when it is re -installed into your pool!
SILENT INSTALLATION AND REMOVAL FEATURE
• The Poolguard system will sound an alarm (Horn will sound) when you install
or remove the pool unit from your pool. If you would like the Poolguard system
not to sound an alarm (Horn will not sound) when you install or remove the pool
unit from your pool, follow the directions below.
1. SILENT INSTALLATION (HORN WILL NOT SOUND)
• Hold the red reset/sleep key on the reset/sleep decal for 1 second until you
hear the pool units horn beep. Remove the red reset/sleep key, you now have 10
seconds to install the pool unit into your pool without the horn sounding. AFTER
10 SECONDS, THE POOL UNITS HORN WILL BEEP INDICATING THAT POOL -
GUARD IS NOW MONITORING YOUR POOL FOR AN INTRUSION. IF THE POOL
UNIT WAS NOT INSTALLED INTO YOUR POOL, IT WILL GO TO SLEEP.
2. SILENT REMOVAL (HORN WILL NOT SOUND)
• Before removing the pool unit from your pool. Place the red reset/sleep key on
the reset/sleep decal for 1 second until you hear the pool units horn beep.
Remove the red reset/sleep key, you now have 5 seconds to remove the pool
unit from your pool without the horn sounding. AFTER 5 SECONDS THE POOL
UNITS HORN WILL BEEP. IMPORTANT: IF THE POOL UNIT WAS REMOVED
FROM YOUR POOL, THE POOL UNIT WILL GO TO SLEEP. BE SURE TO
STORE YOUR ALARM IN THE UPRIGHT POSITION (SEE FIGURE 1). IF THE
POOL UNIT WAS NOT REMOVED FROM YOUR POOL, IT WILL CONTINUE
TO MONITOR YOUR POOL FOR AN INTRUSION. (Cont. on next page) Z%
SILENT INSTALLATION AND REMOVAL FEATURE i
3. POOLGUARD has designed this feature for "ONLY" those who
have the responsibility of removing the alarm from the pool!
BATTERY INSTALLATION / REPLACEMENT
(Battery not included)
POOLGUARD is powered by a standard 9 volt alkaline battery, POOLGUARD
recommends Energizer No. 522. To install or replace the battery:
•Remove the screw from the bottom of the unit, (See Figure 1).
• Carefully slide out electronics assembly; do not pull or jerk on internal
hook up cable. (If necessary, gently shake unit to remove assembly.)
• Remove old battery and check for leakage or corrosion. (Remove any
leakage or corrosion if present before installing new battery.)
IMPORTANT: WHEN A 9 VOLT BATTERY IS FIRST INSTALLED IN THE POOL
UNIT, THE HORN WILL SOUND. TO SILENCE THE ALARM HOLD THE RED
RESET/SLEEP KEY ON THE RESET/SLEEP DECAL FOR 3 TO 4 SECONDS
TO ACTIVATE SLEEP MODE AND SILENCE THE ALARM. THE POOL UNIT
WILL AUTOMATICALLY WAKE UP WHEN IT IS INSTALLED INTO THE POOL.
• Install a new battery by attaching the battery snap (BE SURE THE CONNECTION
IS TIGHT). Slide battery into battery holder.
• Slide the electronic assembly into the pool unit; DO NOT PUT IN UPSIDE DOWN
OR PINCH THE INTERNAL HOOK UP CABLE.
• Replace the screw, hand tighten until screw is all the way in and flush
against the pool unit.
To prevent possible damage, battery should be removed whenever storing
the alarm, for an extended period of time.
ON/OFF INDICATOR - GREEN LED
When POOLGUARD is installed and monitoring your pool for an intrusion, the green LED will flash
once approximately every 10 seconds to indicate that the alarm is ON and OPERATING. When
POOLGUARD is installed in your pool and the alarm is sounding, the green LED will flash
approximately 2 times per second.
When POOLGUARD is removed from your pool the GREEN LED will not flash indicating that
the alarm is OFF and NON -OPERATIONAL.
LOW BATTERY FUNCTION
The POOL UNIT AND THE REMOTE RECEIVER will beep once
approximately every 10 seconds to alert you that the battery is low
in the pool unit and needs to be replaced.
HANDLESCREWS
ELECTRONICS
ASSEMBLY
HORN 1I �
85dB at 10 feet
ASr
ON/OFF INDICATOR INTERNAL
GREEN LED •O'�gATTERY HOOKUP SCREW
HOLDER CABLE
RED RESET/SLEEP DECAL
RESET/SLEEP KEY
PLACEMENT IN YOUR POOL
POOL UNIT
FIGURE 1
UPRIGHT POSITION
Figure 2 illustrates locations best suited for detecting intrusions from any
area of the pool. If your pool is larger than 800 square feet, if you have
more than 2 return lines, any concerns about the size, or if you have
an irregular shaped pool or water features such as waterfalls, please call
customer service to clarify the recommended number of alarms and locations
for alarms: 1-800-242-7163. Poolguard Pool Alarms have been tested and
comply to the ASTM Standard Specifications for Residential Pool Alarms
ASTM F 2208, in a 16'x 32' pool. POOLGUARD alarms can be used in pools
up to 20'x 40' or 800 square feet.
FIGURE 2
Pools 800 Square Feet and Smaller.
(Cont. on next page)
PLACEMENT IN YOUR POOL (Continued)
POOLGUARD automatically compensates for variations in pool levels
within the unit's operating range. The unit utilizes a sensing throat which
projects into the water and is designed to operate in most pools with an
in -wall skimmer. The sensing throat cannot be less than 2.5 inches, (See
Figure 3), and not more than 5.5 inches into the water, POOLGUARD
recommends that the sensing throat be approximately 4 inches in the water
POOLGUARD can be used with SOLAR BLANKETS on the pool.
POOLGUARD can also be used in spas.
12 3/4"
14 1/2"
I3 1/2"
SENSINGTHROAT CANNOT BE LESSTHAN 2.5"IN BLOCKRT
THE WATER, POOLGUARD RECOMMENDS THAT
THE SENSING THROAT BE APPROXIMATELY 4" IN FIGURE 3
THE WATER
IMPORTANT
POOLGUARD may not function properly if your pools water level is not maintained within the required levels of your alarm.
Also, the unit may not operate effectively while certain types of automatic pool cleaners are in operation.
Some irregular shaped decks may not provide a level foundation for the
unit by the pool's edge. This minor problem can be overcome by
appropriately supporting the unit, (See Figure 3).
STABILIZING YOUR POOL ALARM
The Alarm Stabilizing Pin (ASP) is factory installed onto your pool alarm.
Tools needed to install your alarm are: One 5/16" masonry drill bit that can
be found at your local hardware store, a drill, a pencil, a tape measure or yard
stick.
1. Position your pool alarm so that the sensing throat is in the water and
the ASP is touching the deck, (leave a small space no more than 3/8" between
the sensing throat and the top edge of your deck or coping), (See Figure 4).
2. Mark with a pencil the spot where you wish to drill the hole for the ASP.
3. With the 5/16" masonry drill bit, drill a hole 2 1/4" inches deep, as
straight as possible.
(Cont. on next page)
STABILIZING YOUR POOL ALARM (Continued)
4.: Clean off the debris and install the alarm by placing the ASP into the
5/16" diameter by 2 1/4" deep hole.
5. Your Pool Alarm is now ready for use. If you have any questions or need
help with installation, please give us a call at 1-800-242-7163.
6. Be sure to keep the ASP hole clean from debris and dirt so that your
alarm will always lay flat on the pool deck when installed.
REMEMBER THAT THE POOL UNIT MUST BE REMOVED
FROM POOL BEFORE SWIMMING!
ALARMS STABILIZING
21/4"
SMALL SPACE,
NO MORE
THAN 3/8"
WATER
MARK LOCATION FOR 5/16" DIAMETER & 2 1/4"
DEEP HOLE IN DECK
POOL DECK
FIGURE 4
Sensing throat cannot be less than 2.5" in the water, 13001 -GUARD
recommends that the sensing throat be approximately 4" in the water.
TEST BEFORE USING
To ensure effectiveness, test POOLGUARD every time you place it into the
pool by performing the following procedure:
•POOLGUARD DOES NOT HAVE AN ON/OFF SWITCH
When the alarm is in the pool it is always in the ON position and
cannot be turned off. When the alarm is out of the pool it is always
in the OFF position.
•To test your alarm push an object of appropriate volume and weight ofi
the deck edge at the farthest location from the alarm. (A four (4) gallon
jug of water or 3 -one (1) gallon jugs of water tied together are ideal for
testing.) The alarm should sound when the water action caused by the
intrusion reaches the unit. It may take a few seconds for the alarm to
react to the water action.
(Cont. on next page)
TEST BEFORE USING (continued'
*After resetting the alarm and allowing time for the water action to settle,
repeat the procedure from another point in the pool until you are
confident of detection performance.
913001 -GUARD includes a timer function which automatically resets
the unit after the alarm has sounded for approximately 5 minutes.
ADJUSTING YOUR RETURN LINE FITTINGS
The P001 -GUARD alarm should not be placed too close to a return line,
also do not place P001 -GUARD in a location in the pool where a return
line is pointing in the alarms direction. Water turbulence may be too strong,
falsely setting the alarm off or the water turbulence may interfere with the
alarms ability to detect an intrusion. If you have more than 2 return lines
please call customer service at 1-800-242-7163. It is very important in pools
to adjust all the eyeball fittings on your return lines so that the water flow
will not interfere with your pool alarm. Point all the eyeball fittings down
and your pool will still circulate properly and this will allow POOLGUARD
to function properly, (See Fgure 5). Pointing the eyeball fittings down also
helps prevent algae growth.
CORRECT INCORRECT
FIGURE 5
POOLGUARD REMOTE RECEIVER
The POOLGUARD REMOTE RECEIVER has been integrated with the
standard POOLGUARD unit to provide a wireless remote alert operating at
distances of up to 200 feet. The POOLGUARD REMOTE RECEIVER
sounds an alarm in the house when the POOLGUARD unit is activated at
the pool.The remote system consists of the following functional elements:
•A coded pulse receiver (Remote Receiver), (See Figure 6).
•A standard wall outlet power supply, (See Figure 6).
The REMOTE RECEIVER is a compact unit powered by a UL and CSA
approved AC/DC power supply. The REMOTE RECEIVER can be placed
on a table or a counter top inside the house. The pulse coded radio
frequency signal is transmitted from the pool unit and is received and
decoded to sound the remote receiver. The remote receiver will sound
for an additional 3 seconds after the pool unit has been silenced. If
the REMOTE RECEIVER beeps once approximately every 10 seconds,
it is indicating that the 9v battery in the pool unit is low and needs to
be replaced. After you have purchased your POOLGUARD alarm and you
wish to add another remote receiver to your alarm system you can acquire
one from PBM Industries, Inc. Contact PBM by phone or mail or contact
your place of purchase.
POWER SUPPLY—ow-
FIGURE
UPPLY—>
FIGURE 6
B Horn at 10 feet
--*-- REMOTE RECEIVER
TO -OPERATE YOUR REMOTE RECEIVER
Try to locate your REMOTE RECEIVER in a convenient part of your house
close to the pool. Avoid steel walls or any other large metal objects or
obstructions that might interfere with the signal reception. The REMOTE
RECEIVER has to be placed on the same level or a level above the pool in
the house (do not place receiver in an underground basement). The ideal
location for your REMOTE RECEIVER would be by a window overlooking
your pool. Test your REMOTE RECEIVER in different locations in your
house to find the best working place for your receiver. Connect the power
supply to any 120V, electrical outlet and insert the jack into the receiver.
Check that indicator light is on. Your REMOTE RECEIVER unit is now
ready to receive a transmission from your POOLGUARD unit. DO NOT
USE YOUR REMOTE RECEIVER OUTDOORS.
NOTE: THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
SWIMMING POOL SAFETY TIPS
•Supervise children at all times.
• Never permit swimming alone. Never leave a child alone,
even to answer the telephone.
*Always remove the entire solar cover from a pool before swimming.
• Remember that alcohol and water safety do not mix.
• Have your pool area fenced and the gate locked to prevent
unauthorized entry to the pool, and install a gate alarm.
• Lock and secure all doors in the house which permit easy
access to the pool, and install a door alarm.
• Have a responsible adult teach swimming and water safety to your
children.
• Maintain clean, clear water in the pool.
• Do not swim during electrical storms.
• Do not permit bottles, glass, or sharp objects to be used
around the pool.
• Ask your pool dealer how you can improve your pool
safety - they will be glad to assist you.
• Above all: remember that common sense, awareness, and
caution will allow you to enjoy your pool.
WARRANTY AND REPAIRS
POOLGUARD is sold with a limited warranty to cover defects in parts and workmanship for
three years from date of purchase, (retain proof of purchase).
If POOLGUARD exhibits a defect, please call Customer Service at 1-800-242-7163.
Unauthorized returns will not be accepted. Proper repair is only ensured when the unit is
returned to the manufacturer. Visit our website at www.pooiguard.com to fill out your warranty
registration information. The model number and serial number are located on the pool unit.
SEND CORRESPONDENCE TO:
PBM INDUSTRIES, INC.
P.O.BOX 658, NORTH VERNON, IN 47265
1-800-242-7163
This product has been designed to aid in the detection of unwanted intrusions into unsupervised pools.
POOLGUARD IS A SAFETY ALARM SYSTEM AND NOT A LIFE SAVING DEVICE.'This device is not intended
to replace any other safety consideration - i.e., adult supervision, lifeguards, fences, gates, pool covers, locks, etc.,
and some devices may not detect gradual entry'
Foolguard'
10NSF
Sp
'E
PBM INDUSTRIES,~vNc.
Pool®A. %ahss;&
i
REV. 212016
oolguard®
TM`�+Sfl¢
Poolside Unit 10
FALSE ALARMS
Power Suooly
qW
Remote Receiver
All pool alarms will false alarm on occasion for different reasons. False
alarms can be minimized; however, it is important to remember that a false
alarm is better than no alarm at all. WEATHER & WIND—POOLGUARD
sets stationary on the deck of the pool so the wind will not effect the alarm
unit itself. Wind may trigger a false alarm if it is strong enough or steady
enough that it causes the water in the pool to rock or bounce up and
down the pool wall. When the water in the pool moves up and down the
POOLGUARD sensing throat, it may finally cause the alarm to sound.
On extremely windy days when the pool water is rocking it is advised to
remove the POOLGUARD from the pool. Light wind or rain will not effect
the POOLGUARD alarm.
Another false alarm occurs when the pool owner tries to install the alarm
too soon after swimming. After swimming, the water in the pool will rock or
bounce up and down the pool wall for some time depending on the size of
the pool and the type of swimming activity. Before installing the alarm,
after swimming, the pool must be given time to calm. Time will vary
(around 10 to 30 minutes); once the pool owner sees that the pool water is
no longer rocking up and down the pool wall, it is time to install the alarm.
Certain automatic cleaners may set the POOLGUARD unit off in some cases.
If the cleaner head hits the POOLGUARD alarm it may cause it to false alarm.
Solutions to this problem are to use your cleaner at night and your alarm
during the day. Another option would be to find a place around the pool
where the cleaner does not interfere with the alarm. Certain water features
such as waterfalls can cause POOLGUARD to false alarm. To avoid this
problem do not install the POOLGUARD alarm too close to the water feature.
If you are having a problem with any type of water feature call POOLGUARD
at 1-800-242-7163.
ALARM PLACEMENT
The alarm should be on a flat, solid surface for best results. The throat
of the unit is designed to work in most pools with an in -wall skimmer. The
water level up on the throat is important and should be checked. The
sensing throat cannot be less than 2.5 inches in the water, and not more
than 5.5 inches into the water. POOLGUARD recommends that the sensing
throat be approximately 4 inches in the water. POOLGUARD can be used
with a solar cover; however, before removing the cover, the alarm should
be taken out so it does not get pulled into the pool.
ALARM TESTING
Drop something of approximate size, weight and volume of the families
smallest child, the farthest point away from the alarm. A four (4) gallon jug
of water or 3 one (1) gallon jugs of water tied together are ideal for testing.
Remember, when testing you must wait about 15 minutes between
tests for the pool to calm.
ALARM WILL NOT SOUND
CHECK THE CONNECTION BETWEEN THE 9V BATTERY AND THE
BATTERY SNAP. If you are testing and POOLGUARD does not alarm, be sure
you are testing properly — putting your feet in the pool, splashing with your hands,
making waves with a leaf skimmer, or dropping something into the pool that does
not have the proper size, weight and volume will not set the POOLGUARD
alarm off! Testing is very important and should be done correctly.
ALARM HANDLING
The POOLGUARD pool unit is an electronic and mechanical device made
from a sturdy UV rated PVC material. Do not drop POOLGUARD; like any
other appliance, it may break. The POOLGUARD pool unit is water resistant
but not waterproof (sun and rain will not hurt the pool unit). Great care
should be taken not to let the pool unit fall into the pool. If the pool unit does
fall into the pool there are directions on page 2 in this manual on how to dry
it out. Always remember to remove the alarm before using your pool.
REMOTE RECEIVER
When the unit at the pool alarms, the remote receiver will sound.
Maximum Range for the remote is 200 feet from the poolside unit.
Avoid placing remote in basements or close to metal walls. Be sure that
the red light on the remote is on. Remember the poolside unit must be
beeping (alarming) for the remote to work.
If your remote receiver is not getting a clear signal or no signal from the
poolside unit, try the following: Before plugging in the power supply, be
sure to stretch out the cord; do not leave it tied in a bow as packaged.
Your Remote Receiver is similar to a small portable radio. If your remote
is not sounding when the poolside unit is sounding—move the remote
to different locations and stand back for few seconds for the remote
to pick up the signal. You may only have to move your remote a little
to the left or right to bring in the signal—in some cases you might have
to move the remote to a different location or another room. If you cannot
get a signal on your remote receiver CALL CUSTOMER SERVICE AT
1-800-242-7163
•Do read the manual carefully
•Do install a 9 volt battery
9Do untie the bow on the power
•Do test the alarm properly
•Do turn your return line eyeball
bottom of the pool
supply
fittings towards the
•Do remove alarm before swimming
•Do be extremely careful when using an electric
drill around your pool
•DON'T leave alarm in pool while swimming
•DON'T drop your alarm, it may break
•DON'T let your alarm fall into the pool
•DON'T install your alarm immediately after
swimming
•DON'T turn your return eyeball fittings towards the
top of the pool
•DON'T use your alarm on extremely windy days
•DON'T be careless with an electric drill around
your IN GROUND POOL. Extreme caution
should always be used when using electricity
around water!
,APSP
IN GROUND
POOL ALARM
GATE ALARM
14e ota~ Vase cast A"d,
""ce f 98.2.
DOOR ALARM
SOUNDS IMMEDIATELY
"SAFETY BUOY"
ABOVEGROUND
POOLALARM
DOOR ALARM
www.pooiguard.com
Call Toll Free 1-800-242-7163
I m