Loading...
HomeMy WebLinkAboutF2021-0452 - MiscUTILITIES DEPAR o� r DATE: 9/23/2021 uT 9 r pip TO: Mitchell Consulting EMAIL: ablesprk2@gmail.co` F�,. / �v�✓vycrGr F?.r SUBJECT: Static Pressure Test ryT In response to your request, the 84 psi. If you need further assistance, please Sincerely, Matt Aman Utilities Inspector Office: 949-718-3410 Fax: 949-646-5204 Email: Maman@nevrportbeachca.gov Utilities Yard: 949 West 16th Street — Newport Beach, California 92663 - Telephone: (949) 644-3011 — Fax: (949) 646-5204 Mailing Address: Post Office Box 1768, Newport Beach, California 92658-8915 - www.newportbeachca.gov CPVc *ANVIL Figs185 (Formerly Afcon Fig. 513) One Hole Pipe Strap Size Range: 3/4" through Z' Finish: Zinc Plated Steel (Hot -Dip Galvanized optional) Service: Hanger for CPVC pipe in the horizontal position on the side of structural wood beams and Steel 20 Ga. (min) with hanger tab in the upward position only (Fig. A). It can also be used as a guide to limit movement of vertical CPVC pipe with the tab in the horizontal position. Approvals: UL and ULC Listed. Installation: • Place hanger over pipe. • Secure hanger to mounting surface with screws provided. • Steel applications require one (1) #14 x 1" hex washer head self -drilling TEK screw. Not Supplied. Part Number STD -0090. Features: • Beveled edge design helps protect the CPVC pipe from any rough surface. • Easily attaches to wood structure with #10 x 1" hex washer head self threading screw supplied with product. No pre -drilling required. Ordering: Specify CPVC pipe size, figure number and description. Fig. A PROJECT r• rAPPROVAL FIG. 185: DIMENSIONS (IN) a WEIGHT (LBS) Address: [-]Approved as noted CPVC Pipe Size A B oC E F Max. Hanger Spacing (FT.) Approx. Weight/100 (lbs) 8/4 17/e 2'h '/4 11h 1'/4 51h 8 1 13/4 27Ae '/4 11h 11h 6 9 1'/4 ill/10 3 1/4 1'h 17A 6�h 10 1% 17A8 37% '/4 1'/8 2% 7 12 2 2 37/8 '/4 1'h 2% 8 14 PROJECT r• rAPPROVAL Project: []Approved Address: [-]Approved as noted Contractor: []Not approved Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PH -1.18 CPVC /ANVIL Fig* 184 (Formerly Afcon Fig. 515) Double Offset Hanger and Restrainer Size Range. 3/4" through l" Material: Carbon Steel Finish: Pre -Galvanized per ASTM A653 c@ us Service: LISTED • Hanger and surge restraint for horizontal CPVC piping when installed on the side of the supporting structure. • Listed with hardware provided on structural wood beams and composite wood beams (1" minimum). For wood structures with less than 1" thickness, wood blocks may be placed on the backside of the wood structure. #141" fastener pro- vided must be fully engaged in the wood block. ` • May be installed with concrete, steel, and other structural members with fasteners which comply with the requirements of NFPA 13. Approvals: cULus Listed Installation: • Slide CPVC pipe through the double offset hanger and restrainer. • Secure the hanger to the supporting structure with the screws provided or with listed fasteners. Features: • Beveled edge design helps protect the CPVC pipe from any rough surFace and eliminates pipe abrasion. • Easily attaches to wood structure with #14 x V hex washer head self -threading screw supplied with product. No pre -drilling required. • Bottom of pipe is offset 1'/2' from the structure. Eliminates wooden spacer blocks Ordering: Specify CPVC pipe size, figure number and description. p + 0Cx2 B—► L as 11 FIG. 184: DIMENSIONS (IN) • WEIGHT (LBS) CPVC Pipe Size A B 9C H L Max. Hanger Spacing (FT.) Approx. Weight/100 3/a 11/z 1 �/a 31A 5�/e 5�/z 17 1 1�/z 11/2 1/a 31A 51/e 6 17 PROJECT1' 1 Project: APPROVAL , DApproved Address: [-]Approved as noted Contractor: ❑Not approved Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PH -1.18 cpvo a /�1111/IL Fig. 186 (Formerly Afton Fig. 510) TWO Hole Pipe Strap Size Range: 1/4" through 3" Finish: Pre -Galvanized Carbon Steel per ASTM A653 c Service: Hanger for CPVC, steel, & copper pipe in the horizontal position on the bottom usns and side of structural wood beams, composite beams and Steel 20 Ga. (min.) (Fig. A, C� respectively). Can be used as a restrainer when installed on top of structural wood beams (Fig. B)• for limiting pipe movement due to thrust loads during sprinkler system start-up- it ,f can also be used as a guide to limit movement for pipe in the vertical position. When used on composite wood beams, web thickness must be 3/a' or greater.,;' Approvals: cULus Listed _> Installation: • Snap hanger over pipe. • Secure hanger to mounting surface with screws provided. • Do not make adjustments to hanger mounting flanges that result in clamping the pipe to the mounting surface. Pipe must be allowed to move freely through hanger. • Steel applications require two (2) #14 x 1" hex washer head self -drilling TEK screws. Not Supplied. Part Number STD -0090. Features: • Beveled edge design helps protect the CPVC pipe from any rough surface. • Easily attaches to wood structure with #10 x T' hex washer head self threading screw supplied with product. No pre -drilling required. • Retaining dimples hold the strap onto the pipe for ease of installation. (Not shown) Ordering: Specify pipe size, figure number, and description. Fig. A Fig. B Fig. C F FIG. 186: DIMENSIONS (IN) • WEIGHT (LBS) Pipe Size A B eC E F Approx. Weight/100 (lbs) 3/4 1 273/e /4 111A 11% 5 1 11/4 31/4 11/4 6 14/4 15AS 33% 1"/1e 7 11k 1% 37/8 21/5 8 2 179/5 4% 29/8 9 21/e 21/4 53/e 1 /e 27/5 14 3 25/a 65/e 31/z 17 PROJECT INFORMATION APPROVAL STAMP Project: ❑Approved Address: ❑Approved as noted Contractor: [-]Not approved Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PH -3.19 CPVC Z MIVIL Figs, 187 (Formerly Afcon Fig. 511) TWO Hole 900 Side Mount Strap Size Range:'/d'through 2" Finish: Zinc Plated Steel (Hot -Dip Galvanized optional) Service: Hanger for CPVC pipe in the horizontal position on the bottom of structural wood i beams and Steel 20 Ga. (min.) (Fig. A). Can be used as a restrainer, only in Stee/10 Ga. (min) j (Fig. B During installation, adjust hanger mounting flanges such that pipe contacts both r mounting surface and hanger, minimizing vertical pipe movement.' Approvals: UL and ULC Listed. Installation: • Snap hanger over pipe. • Secure hanger to mounting surface with screws provided. • Do not anchor tightly to mounting surface. Pipe must be allowed to move freely through hang • Steel applications require two (2) #14 x 1" hex washer head self -drilling TEK screws. Not Supplied. Part Number STD -0090. Features. c`VL)w rww • Beveled edge design helps protect the CPVC pipe from any rough surface. • Easily attaches to wood structure with #10 x1" hex washer head self threading screw supplied with product. No pre -drilling required. Ordering: Specify CPVC pipe size, figure number and description. Fig. A Fig. B FIG.187: DIMENSIONS (IN) a WEIGHT (LBS) CPVC Pipe Size A B 9C E F Max. Hanger Spacing (FT.) Approx. WeighU100 (lbs) 3/4 N16 112 3/,B 13/18 212 51h 5 1 1 1% 3/10 13VI8 21/4 6 6 11/4 11/18 11/4 '/1B 13/1B .31/4 61/2 7 112 13/B 111/10 3/0 13/6 312 7 6 2 1B/B 210 3/0 13/16 373/6 6 9 PROJEGT INFORMATIONAPPROVAL Project: []Approved Address: ❑Approved as noted Contractor: ❑ Not approved Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PH -11.19 *[SCO Fire & Building Products Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 BlazeMaster 11 CPVC Fire Sprinkler Pipe & Fittings Submittal Sheet General Description Tycoe CPVC Pipe and Fittings pro- duced by Tyco Fire & Building Prod- ucts (TFBP) are designed exclusively for use in wet pipe automatic fire sprin- kler systems. The Tyco CPVC Pipe and Fittings are produced from Blaze- MasterO CPVC compound that is a specially developed thermoplastic compound composed of post chlorin- ated polyvinyl chloride (CPVC) resin and state of the art additives. Tyco CPVC Pipe and Fittings are easier to install than traditional steel pipe sys- tems, and at the same time, provide superior heat resistance and strength as compared to traditional CPVC and PVC piping materials used in the plumbing trade. Various adapters are available to connect CPVC pipe to me- tallic piping. All female pipe thread adapters have brass inserts for dura- bility. Grooved adapters connect di- rectly to grooved end valves and me- tallic pipe, with flexible grooved end couplings. NOTICE Tyco® CPVC Pipe and Fittings pro- duced with BlazeMaster® CPVC com- pound described herein must be in- stalled and maintained in compliance with this document and with the appli- cable standards of the National Fire Protection Association, in addition to the standards of any authorities having jurisdiction. Failure to do so may im- pair the performance of these devices. The owner is responsible for maintain- ing their fire protection system and de- vices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Technical Data Sizes 3/4" to 3" Maximum Working Pressure 175 psi Approvals UL, FM, C -UL, NSF, LPCB, MEA, and the City of Los Angeles. (Refer to In- stallation Handbook IH -1900 dated June 2008 for exact listing/approval information.) Manufacture Source U.S.A. Material • Pipe: ASTM F442, SDR 13.5 • Fittings: ASTM F438 (Sch. 40) and ASTM F439 (Sch. 80), ASTM F1970 Color Orange 0 rapid rresponse7 HOME FIRE SPRINKLER: SYSTEM BlazeMaster® is a registered trademark of The Lubrizol Corporation Page 1 of 2 JUNE, 2008 TFP1915 Page 2 of 2 Installation Tyco® CPVC Pipe and Fittings pro- duced by Tyco Fire & Building Prod- ucts (TFBP) are to be installed in accordance with Installation Hand- book IH -1900 dated June 2008. Care and Maintenance The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The in- stalling contractor or product manufac- turer should be contacted relative to any questions. Automatic sprinkler systems should be Inspected, tested, and maintained by a qualified Inspection Service in accord- ance with local requirements and/or national codes. NOTICE Before closing a fire protection system control valve for inspection or mainte- nance work on the fire protection sys- tem that it controls, permission to shut down the affected fire protection sys- tem must first be obtained from the proper authorities and all personnel who may be affected by this action must be notified. After placing a fire protection system in service, notify the proper authorities and advise those responsible for moni- toring proprietary and/or central sta- tion alarms. Limited Warranty Products manufactured by Tyco Fire & Building Products (TFBP) are war- ranted solely to the original Buyer for ten (10) years against defects in mate- rial and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modi- fied or repaired in accordance with ap- plicable Standards of the National Fire Protection Association, and/or the standards of any other Authorities Having Jurisdiction. Materials found by TFBP to be defective shall be either repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of prod- ucts. TFBP shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. In no event shall TFBP be liable, in contract, tort, strict liability or under any other legal theory, for incidental, indirect, special or consequential dam- ages, including but not limited to labor charges, regardless of whether TFBP was informed about the possibility of such damages, and in no event shall TFBP's liability exceed an amount equal to the sales price. The foregoing warranty is made In lieu of an; and all other warrantiesex- press or irrlplied. including_warranties of merchantability and fitness fora par- ticular purnTsa. This limited warranty sets forth the ex- clusive remedy for claims based on failure of or defect in products, materi- als or components, whether the claim is made in contract, tort, strict liability or any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. © 2008 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 TFP1915 h F Model RC-RES K-Factor: 4.9 a SIN: SS8464 Residential Lead Free Flat Concealed Sprinkler, Pendent C @US LISTED NSF/ANSI/fAN61&3R ED c us The Model RC -RES Residential Flat Concealed Sprinklers are automatic sprinklers of the compressed fusible solder type. They are decorative and fast responding. The Cover Plate Assembly hides the Deflector, Heat Responsive Element etc., which is concealed above the ceiling. The cover plate has a flat profile, and its diameter is extremely small (2-5/8 inch, 68mm). The push -on and/or thread -on, thread -off design of the concealed cover plate assembly allows for easy installation of the cover plate. Therefore, the Model RC -RES should be your first choice when aesthetics is the major consideration for ultimate appeal and unbeatable performance is desired. The Model RC -RES is designed for residential occupancies and is perfect for use in homes, hotels and other living quarters. The Model RC -RES is to be used in wet pipe residential sprinkler systems for One- and Two- Family Dwellings and Manufactured Homes per NFPA 13D; wet pipe residential sprinkler systems for Residential Occupancies up to and Including Four Stories in Height per NFPA 13R; or, wet pipe sprinkler systems for the residential portions of any occupancies per NFPA 13. The Model RC -RES has a 4.9 (70.6 LPM/bar'12) K -factor that meets the required residential flow rates with minimal residual pressure, which allows for smaller pipe sizes and water supply requirements. For extended installation flexibility, the Model RC -RES provides 1/2 inch (12.8mm) vertical adjustment. This adjustment in installation decreases the need for precise cutting of the pipe that drops to the sprinkler and allows for a perfect fit with a range of pipe lengths. The heat sensitivity and water distribution design of Model RC -RES allows for an increased chance of residents to escape or evacuate in case of a fire. However, residential fire sprinkler systems are not a substitute for fire safety awareness or fire safety construction required by building codes. "Lead Free" is defined in the Reduction of Lead in Drinking Water Act (S.3874) endorsed by AWWA:s Water Utility Council, and California Assembly Bill #1953 as having less than or equal to a weighted average of 0.25% lead in wetted surface of pipes, plumbing fittings and fixtures. www.senjusprinkler.com Page 1 of 8 Document NO.U085168.02-08-2021 WARNINGS The Model RC -RES must be installed and maintained in accordance with the rules stated herein as well as in compliance with the applicable standards of the National Fire Protection Association regulations and the standards of any other authorities having jurisdiction. In the event of this condition, consult the authorities having jurisdiction for guidance and approval. Failure to do so may impair the integrity of these devices. It is the responsibility of the installing contractor to provide a copy of this document to the owner or their representative, and in turn, it is the obligation of the owner to provide a copy of this document to a succeeding owner. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any related questions. • Approvals: o cULus Listed • UL -EU Listed (1620F (72°C) only) o NSF/ANSI/CAN 61, NSF/ANSI 372 • Sprinkler Identification Number (SIN): SS8464 • Maximum Working Pressure: 175psi (12.1bar) • Discharge Coefficient (Nominal K Factor): o K = 4.9 GPM/psi"2 (70.6 LPM/bar1M) • Temperature Rating: • 162'F (72°C) Sprinkler with 140°F (6o*q Cover Plate • 205'F (96'C) Sprinkler with 1620F (72°C) Cover Plate • Color Code (Sprinkler) 0 1620F (720C): Uncolored • 205°F (96°C): White • Color Code (Cover Plate) • 140OF (600C): No Mark 0 1620F (720C): White -Colored Mark • Vertical Adjustment: 1/2 inch (12.8 mm) • Cover Plate Finishes: o Standard Finishes: White, Ivory, Beige, Brown, Black, Nickel, Wood Grain o Custom Finishes: Custom color and custom pattern cover plates are available on special order. Contact a Senju Sprinkler representative with any custom orders. Please see chart on Page 8 for more detail. • Physical Characteristics: Ref. Figures 1 and 1.1 , www.senjusprinkler.com Page 2of8 I 2-516' (066mm) or3114'(063mm) Year of Manufacture SSM64 Ipereture Ratl,: 162°Fn2'C or 205 °F196 °C SPKR Qf Body(CopperM[ry) 8 DO.far (Phosphoma Bmn2e) a Gasket(PTFE) 8 Fusible Metal (Solder) s Heat C011eIXor(Coppeq © Cover Plate Assembly Figure 1. Model RC -RES K = 4.9 Cover Plate Sprinkler (Top V1.) (Bottom View) Figure 1.1. Marking (Color Code) Ing: 162°FO2'C or 205 °Flag °C Document NO.UO85168 • 02-08-2021 OPERATION In case of fire, the solder component that holds together the Cover Plate and the Retainer melts. Then the Cover Plate is released at once. As a result, the Deflector drops down to the intended position. Two Heat Collectors are exposed to fire, and when sufficient heat from the fire is reached, internal components of the sprinkler fall apart. This leads to the water flow to be distributed on the affected fire area. (Ref. Figure 2) Normal Condition DESIGN CR Cover Plate Operation Sprinkler Operation Figure 2., Operation Process (For illustrative purposes only) Water Discharge The herein stated rules for use and installation of Model RC -RES are provided by the manufacturer and must be strictly implemented for safe and full results. Notes Residential Fire Sprinkler Systems should only be designed and installed by individuals who are completely familiar with automatic sprinkler system design, installation procedures, and techniques. 6everaicriteria:may apply to ane instanaoon ana usage; or eacn spnnKlecconsequentiy, itis recommenaea that the sprinkler system designer review and develop a working understanding of the complete list of criteria 'prior to Initiating the design of the sprinkler system. Questions concerning sprinkler installation and usage criteria, which are not covered by the following instructions, should be submitted to your contracted company. Include sketches and technical details, as appropriate. In some instances, the requirements of this document may concern specifications which are more stringent, and which take precedence over those specified in NFPA 13, 13D, 13R, or by the authority having jurisdiction. The Model RC -RES must not be used in;applications >where the air pressure above the ceiling is greater than that below. - Inspect all sprinklers after installation to ensure that both the gap: between the cover plate, ceiling and the 6 slots In the cups: are open and free from any air flow impediment. The spray from the sprinkler Is distributed radially outward and downward from the sprinkler deflector. Consequently, the sprinklers must be located such that there will be no blind spaces shielded from spray by partitions, room dividers, overhangs or other parts of the dwelling structure. The number of sprinklers within each compartment (as defined byNFPA 13D, 13R, or 13) must be kept as few as possible while observing all guidelines relating to obstructions and spacing. Use only the Cover Plate provided for the Model RC -RES. The sprinkler must be secured in place: by firmly fastening the sprinkler system piping to the structure. If the sprinkler Is not properly secured imposition, reaction forces resulting from sprinkler operation could alter its orientation and its water distribution pattern. I 44, ii www.senjusprinkler.com Page of 8 Document No.U085168 • 02-08-2021 Obstruction to Water Distribution Locations of sprinklers must follow the obstruction rules of NFPA 13, 13D and 13R for Residential Sprinklers. General Service Conditions The Model RC -RES must only be utilized in WET PIPE sprinkler systems. Heat Source Criteria Referto NFPA 13D, 13R or 13 for the requirements relating to the prevention of possible activation of the Heat Responsive Element of Model RC -RES, due to the exposure of a heat source other than an actual fire. Precautionary Warnings for Corrosive Environments Model RC -RES sprinklers should not be installed where they may be subjected to a corrosive environment including the following: 1. Chlorine ion and Chloride environment Stress corrosion cracking may be caused by exposure to environments with Chlorine ion and Chloride. Exposure to this environment may result in sprinklers operating under Non -Fire conditions or Not Operating when exposed to an actual fire. 2. Sprinkler system piping with Copper Sprinkler systems should be constructed in compliance with the applicable standards and the requirements for copper piping when copper piping is used in the sprinkler system. (Reference standards NFPA 13, ASTM B813, B828, and CDA (Copper Development Association) — Solder Joint) All residual flux must be removed from the interior and exterior of the copper piping by thoroughly flushing before installation of the Sprinkler Heads. Otherwise, residues of flux may cause corrosion and/or leakage in the sprinkler system. Hydraulic Design Criteria The minimum required sprinkler flow rates for systems designed to NFPA 13D or 13R are given in Table A as a function of temperature rating and the maximum allowable coverage area. The sprinkler flow rate is the minimum required discharge from the most hydraulically demanding sprinkler from each of the total number of "design sprinklers" as specified in NFPA 13D or 13R. For systems designed to NFPA 13, the number of designed sprinklers is to be the four most hydraulically demanding sprinklers. The minimum required discharge from each of the four sprinklers is to be the greater of the following: • The flow rates given in Table A for NFPA 13D and 13R as a function of temperature rating and maximum allowable coverage area. • A minimum discharge of 0.1GPM/sq.ft. [4.07LPM/sq.m] over the "design area" comprised of the four most hydraulically demanding sprinklers for the actual coverage area being protected by the four sprinklers. www.senjusprinkler.com Page 4 of 8 Document No.U085168 •02-08-2021 Available Sprinkler Temperature Ratings Temperature Classification Sprinkler Nominal Temperature Rating Maximum Ambient Ceiling Temperature Temperature Rating of the Cover Plate Assembly Ordinary 162°F (72°C) 100°F (38°C) 140°F (60°C) Intermediate 205°F (96°C) 150°F (66°C) 162°F (72°C) Precautionary Warnings for Corrosive Environments Model RC -RES sprinklers should not be installed where they may be subjected to a corrosive environment including the following: 1. Chlorine ion and Chloride environment Stress corrosion cracking may be caused by exposure to environments with Chlorine ion and Chloride. Exposure to this environment may result in sprinklers operating under Non -Fire conditions or Not Operating when exposed to an actual fire. 2. Sprinkler system piping with Copper Sprinkler systems should be constructed in compliance with the applicable standards and the requirements for copper piping when copper piping is used in the sprinkler system. (Reference standards NFPA 13, ASTM B813, B828, and CDA (Copper Development Association) — Solder Joint) All residual flux must be removed from the interior and exterior of the copper piping by thoroughly flushing before installation of the Sprinkler Heads. Otherwise, residues of flux may cause corrosion and/or leakage in the sprinkler system. Hydraulic Design Criteria The minimum required sprinkler flow rates for systems designed to NFPA 13D or 13R are given in Table A as a function of temperature rating and the maximum allowable coverage area. The sprinkler flow rate is the minimum required discharge from the most hydraulically demanding sprinkler from each of the total number of "design sprinklers" as specified in NFPA 13D or 13R. For systems designed to NFPA 13, the number of designed sprinklers is to be the four most hydraulically demanding sprinklers. The minimum required discharge from each of the four sprinklers is to be the greater of the following: • The flow rates given in Table A for NFPA 13D and 13R as a function of temperature rating and maximum allowable coverage area. • A minimum discharge of 0.1GPM/sq.ft. [4.07LPM/sq.m] over the "design area" comprised of the four most hydraulically demanding sprinklers for the actual coverage area being protected by the four sprinklers. www.senjusprinkler.com Page 4 of 8 Document No.U085168 •02-08-2021 Table A. NFPA 13D & 13R Wet Pipe Hydraulic Design Criteria for Model SS8464 For systems with ceiling types smooth flat horizontal, or beamed, or sloped, in accordance with NFPA 13D, 13R or 13 as applicable. Maximum Maximum Ordinary Temperature Intermediate Temperature Coverage Spacing Gating 162°F (72°C) Gating 206°F (96°C) De6ecter to Installation Minimum 01 Ft. Ft. Ft' Ceiling TYPe Spacing Ft.(m) Flowo)GPM Pressuref°l Flowm)GPM Pressures) (m x m) (m) (LPM) PSI (bar) (LPM) PSI (bar) 12x12 12 13 7.0 13 7.0 Smooth (3.7x3.7) (3.7) (49.2) (0.48) (49.2) (0.48) Ceilings 3/8 to 7/8 Inches. 14 x 14 14 13 7.0 13 7.0 (4.3 x 4.3) (4.3) (49.2) (0.48) (49.2) (0.48) Beamed Ceilings per 16x16 16 13 7.0 13 7.0 NFPA I3D, Concealed 8 (4.9x4.9) (4.9) (49.2) (0.48) (49.2) (0.4B) 13R or 13. Installed in (2.4) 18 x 18 18 17 12.0 17 12.0 (5.5 x 5.5) (5.5) (64.4) (0.83) (64.4) (0.83) beam 3/8 to 7/8 inches below bottom 20 x 20 20 21 18.4 21 18.4 (6.1x6.1) (6.1) (79.5) (1.27) (79.5) (1.27) of beam. a. For coverage area dimensions less than the above mentioned, it needs to use the minimum required flow for the Next Higher Coverage Area listed. b. Requirement is based on minimum flow in GPM (LPM) from each sprinkler. The associated residual pressures are calculated using the nominal K -Factor. Refer to Hydraulic Design Criteria Section for details. Sprinkler Spacing Criteria The minimum spacing between sprinklers is 8 feet (2.4m). The maximum spacing between sprinklers cannot go beyond the coverage area calculated by using the specific hydraulic factors. (Ref. Table A) INSTALLATION The Model RC -RES must be installed in accordance with the following instructions: NOTES Do not: use any sprinklers which have been subjected to potential mechanical damage. Do not use any sprinklers which show deformation or cracking in either the Sprinkler or the Protective Cap. Prior to installation, sprinklers should be maintained in the original cartons and; packaging until used to minimize the potential for: damage to the sprinklers that: could cause: improper operation or non -operation. The Protective Cap must remain on the sprinkler during installation. After the Installation is completed, the Protective Cap must be removed to place the sprinkler In service. Use a torque of 7 to 14 ft -lbs (9:5 to 19.0 N -m) to achieve a 1/2 inch NPT sprinkler joint. If you exceed the recommended maximum torque; this could result In damage to the sprinkler inlet, which may lead to leakage from the sprinkler.: Use only NR -H model wrenchsocket for Installation of RC -RES sprinklers. Use of any other wrench or socket is prohibited and may cause damage to the sprinkler. In case of insufficient adjustment in Cover Plate installation, do not try to overly tighten, screw the sprinkler too loosely or make any modification to the cover. plate assembly. Readjust the sprinkler fitting for. a better fit..` Do not rotate the Cap Removal Tool for RC to the left with force when placing the two hook arms into place. The installed sprinkler may become loosened, which may cause water leakage. 44 www.senjusprinkler.com Page 5 of 8 Document No.U085168 • 02-08-2021 Installation Steps Step 1: The installation requirements for the sprinkler are as follows: to be installed only in the pendent position with the waterway perpendicular to the ceiling. Install the sprinkler fitting so that the distance from the face of the fitting to the mounting surface will be nominally 2 inches (50.8mm) as shown in Figure 3. Step 2: With pipe thread sealant applied to the threads, hand tighten the sprinkler into the sprinkler fitting. Then tighten it with the Socket NR -H or Ratchet (3/8" drive) & Socket NR -H Combination (Ref. Figure 4). The teeth of the Socket must fit perfectly with the grooves on the Sprinkler for proper installation (Ref. Figure 4). Step 3: If desired, the Protective Cap may also be used to locate the center of the clearance hole by gently pushing the ceiling material against the center point of the Protective Cap. Before the installation of the ceiling, the sprinkler installation can be started with a 2-3/8 inch (60mm) diameter clearance hole (Ref. Figure 3). Use the "Vertical Adjustment" indicator on the Protective Cap to check for proper installation height (Ref. Figure 3). Correct Incorrect Figure 2 Installation Figure 4: Ratchet & Socket Step 4: Use the Cap Removal Tool for RC to remove the Protective Cap (Ref. Figure 5), and then push or screw a Cover Plate Assembly on the Cup of the Sprinkler by hand until its flange just has contact with the ceiling (Ref. Figure 6 and Figure 7). Stop tightening the Cover Plate Assembly once the flange has contact with the ceiling. If the ceiling has been lifted from its normal position in the process of tightening the Cover Plate Assembly, readjust the cover plate assembly as necessary. If the flange of the Cover Plate Assembly cannot contact the ceiling sufficiently, readjust the sprinkler fitting as necessary. When properly installed, there is a nominal 1/16 inch (1.6mm) air gap between the lip of the Cover Plate and the ceiling, as shown in Figure 6. Step 1 Step 2 Figure 5: Protective Cap Removal Pull down Step 3 63 www.senjusprinkleccom Page 6 of 8 Document No.U085168 • 02-08-2021 ., 258'su..re(.68mml Figure 6: Installation (Cover Plate Assembly) Incorrect Correct Incorrect Figure 7: Installation (Correct and Incorrect) The following instructions must be implemented for the maintenance and service of the Model RC -RES. Notes Wet pipe sprinkler systems must be maintained at a minimum temperature of 40°F 1400 to prevent freezing and bursting of the pipe and/or sprinklers. Automatic sprinklers are not to be tested with a heat source. Operation of the heat responsive element can result. Absence of a Cover Plate Assembly may delay the response time of the sprinkler in case of fire. Install the cover plate assembly properly, as shown in Figure 6. Improper installation of the cover plate assembly may cause improper operation or non -operation. If the ceiling is to be repainted after the installation of the Sprinkler, care must be exercised to ensure that the new paint does not sea[ off any of the air gap. factory applied paint may adversely delay or prevent sprinkler operation in case of a fire. Do not pull the Cover Plate. Separation may result. In preparation for maintenance of the fire protection system, permission to close the main control valve must be obtained from the proper authorities,: and all: affected partles by this action, and must be informed before the maintenance session can commence. Do NOT enclose any sprinklers: within drapes, curtains, or valances. Do NOT hang anything from the sprinklers. r Do NOT clean the sprinklers with soap and/or water, detergents, ammonia, cleaning fluids, or other chemicals. Remove dust, lint, cobwebs, cocoons, insects, and larvae by gently brushing with a feather duster or gently vacuuming with a soft bristle 0.0., dusting) brush attachment. Exercise suitable safety precautions in the use and storage of highly flammable materials. The rapid rate of fire development and spread of these materials can reduce the ability of the sprinkler system to aid In the control of a fire Involving. such hazards: . www.senjusprinkler.corn Page 7 of 8 Document No.1-1085168.02-08-2021 Leaking or corroded sprinklers must be replaced. Automatic Sprinklers must be kept In a cool and dry place. Automatic sprinklers must never be physically altered, such as painted, plated, :or coated, once shipped from the factory. If the sprinklers have been in any way modified, they must be replaced. Great caution must be applied to prevent damage to the sprinklers at all stages -before, during, and after installation: Damaged units because of dropping, hitting, over -tightening, or wrench slippage, must be replaced. The Model RC -RES must only be replaced with pendent sprinklerswhich' are listed for residential fire: protection service and which have the same nominal K -Factor, the same coverage area, and the same: or: lower flow ratings (as Indicated' under Table A ;'Hydraulic Design Criteria"). When remodeling, such as by adding false beams or light fixtures or changing the location of compartment walls, firstverify that the new construction will not violate the Installation requirements of the applicable standards of NFPA. Alterthe new construction and/or the sprinkler system to suit the requirements of this document and the applicable NFPA regulations. The owner is responsible for the maintenance of the sprinkler system, Including Inspection: and testing of its compliance with this document, as well as the standards of the National'. Fire Protection Association (e.g., NFPA 25), and the regulations of any other authorities having jurisdiction. The owner should 'direct any questions regarding the above rules and regulations to the Installing' contractors' or the sprinkler manufacturer. It is recommended that automatic sprinkler systems be Inspected, tested, and maintained by a'qualifled Inspection Service In accordance with NFPA 25. LIMITED WARRANTY For details of warranty, refer to Sales Contract. ORDER PROCEDURE When placing an order, please contact a local distributor with the following information (Model Name, Temperature Rating and Finish). Sprinkler • Model: RC -RES SIN: SS8464, Residential Flat Concealed Sprinkler, Pendent, K4.9, Temperature: 162°F (72°C) or 205°F (96°C) Cover Plate Assembly • 2-5/8 inch ((p68mm) or 3-1/4 inch (�83mm) or 2-5/8 inch square (o68mm), Order separately from Sprinkler Please refer to the chart below for available sizes, temperature, and finishes. Tools & Accessories • Socket NR -H • Cap Removal Tool for RC for use with a 3/8" drive ratchet (not included) • Cover Plate Installation Tool • Socket NR -H Plastic for use with a 1/2" drive ratchet (not included) www.senjusprinkler.com Page 8 of 8 Document No.U085168 •02-08-2021 Standard Brown Finishes Black Nickel Copper Wood Grain Custom I Finishes Custom Custom Color Pattern White Ivory Beige 2-5/8" Round, 140°F (a (a - - - 10 OO 3-1/4" Round, 140"F O O O O O O OO OO OO OO 2-5/8" Square, 140°F Q - - - O O 2-5/8" Round, 162°F O O O 3-1/4" Round, 162°FO OO OO © O O OO 2-5/8" Square, 162"F O O OO Tools & Accessories • Socket NR -H • Cap Removal Tool for RC for use with a 3/8" drive ratchet (not included) • Cover Plate Installation Tool • Socket NR -H Plastic for use with a 1/2" drive ratchet (not included) www.senjusprinkler.com Page 8 of 8 Document No.U085168 •02-08-2021 CPVC ANVIL Fig.188R (Formerly Afcon Fig. 514) Two Hole Standoff Hanger & Restrainer Size Range:'/," through 2" Material: Carbon Steel Finish: Pre -Galvanized per ASTM A653 Service: • Hanger and surge restraint for horizontal CPVC, steel, and copper piping when installed on the top, bottom, and side of the supporting structure. • Guide for vertical CPVC, steel, and copper piping when installed on the side of the supporting structure. • Horizontal and vertical seismic restraint per NFPA 13-2016 requirements. • May be installed with concrete, steel structural members, and other structural members with fasteners which comply with the requirements of NFPA 13. Approvals: cULus Listed Patents: No. 6,648,278 Installation: • Snap hanger over pipe. If needed, squeeze strap back around pipe. • CPVC pipe must be allowed to slide freely through the Fig. 188R. • Secure hanger to mounting surface with screws provided or with listed fasteners. Features: • Beveled edge design helps protect the CPVC pipe from any rough surface and eliminates pipe abrasion. • Easily attaches to wood structure with #10 x V hex washer head self -threading screw supplied with product. No pre -drilling required. • Bottom of pipe is offset 11/2' from the structure. Eliminates wooden spacer blocks. Ordering: Specify CPVC pipe size, figure number and description. Hangs Restra Hanger & Restrainer Installation - Backing Nut Hanger =1 - at top fastener Restraint = 2 - on each fastener a & Per NFPA-130 and NFPA-13R •ainer PROJECTr 1 Project: APPROVAL LjApproved Address: Approved as noted Contractor: Not approved Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PH -07.20 CPVC Fig.188R (Formerly Afton Fig. 514) lkvo Hole Standoff Hanger & Restrainer (cont) Hanger and Restrainer limp 1 Las I rilm Will 11 .100, ,'1 FIG. 188R. DIMENSIONS (IN) • WEIGHT (LBS) CPUC Pipe Size A B oC D E F G Max. Hanger Spacing (FT.) Approx. Weight/100 (Ibs) 3/a 23/4 3'h %4 2 1 2% 1'h 5% 11 1 213/e 31h /4 23% 1 275/e 1/2 6 12 14/4 273/ie 31h 1/4 Vie 1 3�/4 11/2 61h 13 11/2 355% 'd :d dd. d 14 2 311/e 43/8 1/4 211/e 1 4 11/2 8 16 dOO a a. a a' Hanger and Restrainer limp 1 Las I rilm Will 11 .100, ,'1 FIG. 188R. DIMENSIONS (IN) • WEIGHT (LBS) CPUC Pipe Size A B oC D E F G Max. Hanger Spacing (FT.) Approx. Weight/100 (Ibs) 3/a 23/4 3'h %4 2 1 2% 1'h 5% 11 1 213/e 31h /4 23% 1 275/e 1/2 6 12 14/4 273/ie 31h 1/4 Vie 1 3�/4 11/2 61h 13 11/2 355% 4�/4 1/4 27/e 1 31/2 11/2 7 14 2 311/e 43/8 1/4 211/e 1 4 11/2 8 16 FIG. 188R- LISTED FASTENERS Pipe Wood and Composite Beams Steel (18go. Minimum) CPUC Screw Supplied or #10 x 1"TEK Screw #14 x 1"TEK Screw or 1/4" x 1"TEK Screw Steel&Copper #14x1"TEKScrew ort/4"x1'1"Lag Screw #14 x 1 " TEK Screw ort/4"x1"TEKScrew PH -07.20 CPVC Figs, 188 TWO Hole Standoff Strap Size Range:3/4" through 2" Finish: Zinc Plated Steel (Hot -Dip Galvanized optional) Service. Hanger for CPVC pipe in the horizontal position on the bottom of structural wood beams and steel 20ga. min. (Fig. B). It can also be used as a guide to limit movement for a pipe in the horizontal/vertical position on the side of structural wood beams, composite wood beams and steel 20ga. min. (Fig. A), c �� Approvals: UL and ULC Listed, us usreo Installation: • Snap hanger over pipe. • Position hanger back around pipe but allow for pipe movement. • Secure hanger to mounting surface with screws provided. Recheck to insure that the pipe is allowed to move freely through hanger. • Steel applications require two (2) #14 x 1" hex washer head self -drilling TEK screws. Not Supplied. Part Number STD -0090. Features: • Beveled edge design helps protect the CPVC pipe from any rough surface. • Easily attaches to wood structure with #10 x 1" hex washer head self threading screw supplied with product. No pre -drilling required. • Eliminates wooden spacer blocks. Ordering: Specify CPVC pipe size, figure number and description. Note. If UL listed restraint is required, use Anvil Fig. 188R (Formerly Afcon Fig, 514). e A be E fe Fig. A Fig. B FIG. 188: DIMENSIONS (IN) a WEIGHT (LBS) APPROVAL DApproved Address: CPUC Pipe Size A B 0C E F Max. Hanger Approx. Notes 1: Notes 2: Spacing (FT.) Weight/100 (lbs) 3/4 11/16 3�/4 1/4 VA 2% 5'/e 5 1 13/8 3% 4/4 1 t'A 3 6 6 1Y4 14/3 3"tie t/4 1Y8 33% 6'Az 7 74/z 1r/8 43/s 4/4 14/8 3%e 7 a 2 2 44/2 4/4 14/8 44/8 8 9 PROJECT INFORMATION Pro)ecl: APPROVAL DApproved Address: ❑Approved as noted Contractor: []Not approved Engineer: Remarks: Submittal Date: Notes 1: Notes 2: -.8